View MB96345_7777252.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

fme-mb96340 rev 10 fujitsu semiconductor data sheet copyright ?2010 fujitsu semiconductor limited all rights reserved 2010.6 for the information for microcontroller supports, see the following web site. this web site includes the "customer design review supplement" which provides the latest cautions on system development and the minimal requirements to be checked to prevent problems before the system development. http://edevice.fujitsu.com/micom/en-support/ 16-bit proprietary microcontroller cmos f 2 mc-16fx mb96340 series MB96345/346 mb96f345 *1 mb96f346/f347/f348 description mb96340 series is based on fujitsus advanced 16fx architecture (16-bit with instruction pipeline for risc-like performance). the cpu uses the same instruction set as the established 16lx series - thus allowing for easy migration of 16lx software to the new 16fx products. 16fx improvements compared to the previous generation include signi?antly improved performance - even at the same operation frequency, reduced power consumption and faster start-up time. for highest processing speed at optimized power consumption an internal pll can be selected to supply the cpu with up to 56mhz operation frequency from an external 4mhz resonator. the result is a minimum instruction cycle time of 17.8ns going together with excellent emi behavior. an on-chip clock modulation circuit signi?antly reduces emission peaks in the frequency spectrum. the emitted power is minimized by the on-chip voltage regulator that reduces the internal cpu voltage. a ?xible clock tree allows to select suitable operation frequencies for peripheral resources independent of the cpu speed. *1: these devices are under development and speci?ation is preliminary. these products under development may change its speci?ation without notice. note: f 2 mc is the abbreviation of fujitsu flexible microcontroller www.datasheet.in
mb96340 series 2 fme-mb96340 rev 10 features feature description technology 0.18 m cmos cpu ? 2 mc-16fx cpu up to 56 mhz internal, 17.8 ns instruction cycle time optimized instruction set for controller applications (bit, byte, word and long-word data types; 23 different addressing modes; barrel shift; variety of pointers) 8-byte instruction execution queue signed multiply (16-bit 16-bit) and divide (32-bit/16-bit) instructions available system clock on-chip pll clock multiplier (x1 - x25, x1 when pll stop) 3 mhz - 16 mhz external crystal oscillator clock (maximum frequency when using ceramic resonator depends on q-factor). up to 56 mhz external clock for devices with fast clock input feature 32-100 khz subsystem quartz clock 100khz/2mhz internal rc clock for quick and safe startup, oscillator stop detection, watchdog clock source selectable from main- and subclock oscillator (part number suffix ?? and on-chip rc oscillator, independently for cpu and 2 clock domains of peripherals. low power consumption - 13 operating modes : (different run, sleep, timer modes, stop mode) clock modulator on-chip voltage regula- tor internal voltage regulator supports reduced internal mcu voltage, offering low emi and low power consumption figures low voltage reset reset is generated when supply voltage is below minimum. code security protects rom content from unintended read-out memory patch function replaces rom content can also be used to implement embedded debug support dma automatic transfer function independent of cpu, can be assigned freely to resources interrupts fast interrupt processing 8 programmable priority levels non-maskable interrupt (nmi) timers three independent clock timers (23-bit rc clock timer, 23-bit main clock timer, 17-bit sub clock timer) watchdog timer www.datasheet.in
mb96340 series fme-mb96340 rev 10 3 can supports can protocol version 2.0 part a and b iso16845 certified bit rates up to 1 mbit/s 32 message objects each message object has its own identifier mask programmable fifo mode (concatenation of message objects) maskable interrupt disabled automatic retransmission mode for time triggered can applications programmable loop-back mode for self-test operation usart full duplex usarts (sci/lin) wide range of baud rate settings using a dedicated reload timer special synchronous options for adapting to different synchronous serial protocols lin functionality working either as master or slave lin device i 2 c up to 400 kbps master and slave functionality, 7-bit and 10-bit addressing a/d converter sar-type 10-bit resolution signals interrupt on conversion end, single conversion mode, continuous conversion mode, stop conversion mode, activation by software, external trigger or reload timer a/d converter refer- ence voltage switch 2 independent positive a/d converter reference voltages available reload timers 16-bit wide prescaler with 1/2 1 , 1/2 2 , 1/2 3 , 1/2 4 , 1/2 5 , 1/2 6 of peripheral clock frequency event count function free running timers signals an interrupt on overflow, supports timer clear upon match with output compare (0, 4), prescaler with 1, 1/2 1 , 1/2 2 , 1/2 3 , 1/2 4 , 1/2 5 , 1/2 6 , 1/2 7 ,1/2 8 of peripheral clock frequency input capture units 16-bit wide signals an interrupt upon external event rising edge, falling edge or rising & falling edge sensitive output compare units 16-bit wide signals an interrupt when a match with 16-bit i/o timer occurs a pair of compare registers can be used to generate an output signal. feature description www.datasheet.in
mb96340 series 4 fme-mb96340 rev 10 programmable pulse generator 16-bit down counter, cycle and duty setting registers interrupt at trigger, counter borrow and/or duty match pwm operation and one-shot operation internal prescaler allows 1, 1/4, 1/16, 1/64 of peripheral clock as counter clock and reload timer underflow as clock input can be triggered by software or reload timer real time clock can be clocked either from sub oscillator (devices with part number suffix ??, main oscillator or from the rc oscillator facility to correct oscillation deviation of sub clock or rc oscillator clock (clock calibration) read/write accessible second/minute/hour registers can signal interrupts every half second/second/minute/hour/day internal clock divider and prescaler provide exact 1s clock external interrupts edge sensitive or level sensitive interrupt mask and pending bit per channel each available can channel rx has an external interrupt for wake-up selected usart channels sin have an external interrupt for wake-up non maskable interrupt disabled after reset once enabled, can not be disabled other than by reset. level high or level low sensitive pin shared with external interrupt 0. external bus interface 8-bit or 16-bit bidirectional data up to 24-bit addresses 6 chip select signals multiplexed address/data lines wait state request external bus master possible timing programmable alarm comparator monitors an external voltage and generates an interrupt in case of a voltage lower or higher than the defined thresholds threshold voltages defined externally or generated internally status is readable, interrupts can be masked separately feature description www.datasheet.in
mb96340 series fme-mb96340 rev 10 5 i/o ports virtually all external pins can be used as general purpose i/o all push-pull outputs (except when used as i2c sda/scl line) bit-wise programmable as input/output or peripheral signal bit-wise programmable input enable bit-wise programmable input levels: automotive / cmos-schmitt trigger / ttl (ttl levels not supported by all devices) bit-wise programmable pull-up resistor bit-wise programmable output driving strength for emi optimization packages 100-pin plastic qfp and lqfp flash memory supports automatic programming, embedded algorithm write/erase/erase-suspend/resume commands a flag indicating completion of the algorithm number of erase cycles: 10,000 times data retention time: 20 years erase can be performed on each sector individually sector protection flash security feature to protect the content of the flash low voltage detection during flash erase feature description www.datasheet.in
mb96340 series 6 fme-mb96340 rev 10 product lineup features mb96v300b mb96(f)34x product type evaluation sample flash product: mb96f34x mask rom product: mb9634x product options ys na low voltage reset persistently on / single clock rs low voltage reset can be disabled / single clock yw low voltage reset persistently on / dual clock rw low voltage reset can be disabled / dual clock ts indep. 32kb flash / low voltage reset persistently on / single clock hs indep. 32kb flash / low voltage reset can be disabled / single clock tw indep. 32kb flash / low voltage reset persistently on / dual clock hw indep. 32kb flash / low voltage reset can be disabled / dual clock fs 64kb data flash / low voltage reset persistently on / single clock ds 64kb data flash / low voltage reset can be disabled / single clock fw 64kb data flash / low voltage reset persistently on / dual clock dw 64kb data flash / low voltage reset can be disabled / dual clock as no can / low voltage reset can be disabled / single clock devices cs no can / indep. 32kb flash / low voltage reset can be disabled / single clock aw no can / low voltage reset can be disabled / dual clock cw no can / indep. 32kb flash / low voltage reset can be disabled / dual clock flash/rom ram 160kb 8kb rom/flash memory emulation by external ram, 92kb internal ram MB96345y *1 , MB96345r *1 224kb [flash a: 160kb, data flash a: 64kb] 8kb mb96f345f *1 , mb96f345d *1 288kb 16kb mb96f346y, mb96346y *1 , mb96f346r, mb96346r *1 , mb96f346a 416kb 16kb mb96f347y, mb96f347r, mb96f347a 544kb 24kb mb96f348y, mb96f348r, mb96f348a 576kb [flash a: 544kb, flash b: 32kb] 24kb mb96f348t, mb96f348h, mb96f348c package bga416 fpt-100p-m20 fpt-100p-m22 www.datasheet.in
mb96340 series fme-mb96340 rev 10 7 *1: these devices are under development and speci?ation is preliminary. these products under development may change its speci?ation without notice. dma 16 channels 6 channels usart 10 channels 7 channels i2c 2 channels 2 channels a/d converter 40 channels 24 channels a/d converter reference voltage switch yes yes (except mb96f345dyy or mb96f345fyy) 16-bit reload timer 6 channels + 1 channel (for ppg) 4 channels + 1 channel (for ppg) 16-bit free-running timer 4 channels 2 channels 16-bit output compare 12 channels 8 channels 16-bit input capture 12 channels 8 channels 16-bit programmable pulse generator 20 channels 16 channels can interface 5 channels mb96(f)34xayy or mb96(f)34xcyy: no mb96f345dyy or mb96f345fyy: 1 channel others: 2 channels external interrupts 16 channels non-maskable interrupt 1 channel real time clock 1 i/o ports 136 80 for part number with suf? "w", 82 for part number with suf? "s" alarm comparator 2 channels mb96f345dyy or mb96f345fyy: no others: 2 channels external bus interface yes yes (multiplexed address/data) chip select 6 signals clock output function 2 channels low voltage reset yes on-chip rc-oscillator yes features mb96v300b mb96(f)34x www.datasheet.in
mb96340 series 8 fme-mb96340 rev 10 block diagram block diagram of mb96(f)34x flash memory b or data flash a *2 i2c 2 ch. sda0, sda1 scl0, scl1 dma controller boot rom peripheral bus bridge peripheral bus bridge 16fx core bus (clkb) usart 7 ch. 10-bit adc 24 ch. alarm comparator 2 ch. *4 16-bit reload timer 4 ch. i/o timer 0 icu 0/1/2/3 ocu 0/1/2/3 16-bit ppg 16 ch. can interface 2 ch. external interrupt real time clock watchdog ram voltage regulator sin0...sin3, sin2_r, sin7_r...sin9_r sot0...sot3, sot2_r, sot7_r...sot9_r sck0...sck3, sck2_r, sck7_r...sck9_r alarm0 *4 alarm1 *4 wot av cc av ss avrh avrl/avrh2 *5 an0 ... an23 adtg, adtg_r tin0 ... tin3 tot0 ... tot3 frck0 in0 ... in3 out0 ... out3 int0 ... int15 tx0, tx1 *3 rx0, rx1 *3 peripheral bus 1 (clkp1) peripheral bus 2 (clkp2) v cc v ss c ppg0 ... ppg15 ttg0 ... ttg15 i/o timer 1 icu 4/5/6/7 ocu 4/5/6/7 frck1 in4 ... in7 out4 ... out7 16fx cpu interrupt controller clock & mode controller flash memory a memory patch unit ad00 ... ad15 a16 ... a23 ale rdx wr(l)x, wrhx hrq hakx rdy eclk external bus interface lbx, ubx cs0 ... cs5 nmi, nmi_r *2: flash b only available on mb96f34xcyy, mb96f34xhyy or mb96f34xtyy int0_r ... int2_r int3_r1 ckot0, ckot1 ckotx0, ckotx1 x0, x1 x0a, x1a *1 rstx md0...md2 int4_r, int5_r int7_r ... int15_r *1: x0a, x1a only available on mb96(f)34xywy *3: can interfaces are not available on mb96(f)34xayy or mb96(f)34xcyy rlt6 data flash a only available on mb96f34xdyy or mb96f34xfyy can1 is not available on mb96f345dyy or mb96f345fyy *4: alarm comparator is not available on mb96f345dyy or mb96f345fyy *5: a/d converter reference voltage switch is not available on mb96f345dyy or mb96f345fyy www.datasheet.in
mb96340 series fme-mb96340 rev 10 9 pin assignments pin assignment of mb96(f)34x (fpt-100p-m22) remark: mb96(f)34x products are pin-compatible to f 2 mc-16lx family mb90340 series. 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1 234 567 9 8 qfp - 100 package code (mold) fpt-100p-m22 (fpt-100p-m22) md1 md2 p00_0/ad00/int8/sck7_r p10_1/tx0 *2 p10_0/rx0/int8_r *2 p09_7/out3/cs0 p09_6/out2/cs1 p09_5/out1/cs2 p09_4/out0/cs3 p09_3/ppg11/cs4 p09_2/ppg10/cs5 p09_1/ppg9/lbx p09_0/ppg8/ubx vss vcc p08_7/sck1 p08_6/sot1 p08_5/sin1/int1_r p08_4/sck0/int15_r p08_3/sot0/tot2 p08_2/sin0/tin2/int14_r p08_1/tot0/ckot0/int13_r p08_0/tin0/ckotx0/adtg/int12_r p07_7/an23/int7/sin9_r p07_6/an22/int6/sot9_r rstx md0 p00_1/ad01/int9/sot7_r p00_2/ad02/int10/sin7_r p00_3/ad03/int11/sck8_r p00_4/ad04/int12/sot8_r p00_5/ad05/int13/sin8_r p00_6/ad06/int14 p00_7/ad07/int15 p01_0/ad08/ckot1/tin1 p01_1/ad09/ckotx1/tot1 p01_2/ad10/int11_r/sin3 p01_3/ad11/sot3 p01_4/ad12/sck3 p01_5/ad13/int7_r/sin2_r p01_6/ad14/sot2_r p01_7/ad15/sck2_r p02_0/a16/ppg12 p02_1/a17/ppg13 p02_2/a18/ppg14 p02_3/a19/ppg15 vcc vss x1 x0 p02_4/a20/ttg8/ttg0/in0 p02_6/a22/in2/ttg2/ttg10 p02_7/a23/in3/ttg3/ttg11 p03_0/ale/in4/ttg4/ttg12 p03_1/rdx/in5/ttg5/ttg13 p03_2/wrlx/wrx/int10_r p03_3/wrhx p03_4/hrq/out4 p03_5/hakx/out5 p03_6/rdy/out6 p03_7/eclk/out7 x0a/p04_0 *1 x1a/p04_1 *1 vcc vss c p04_2/in6/rx1/int9_r/ttg6/ttg14 *2 p04_3/in7/tx1/ttg7/ttg15 *2 p04_4/sda0/frck0 p04_5/scl0/frck1 p04_6/sda1 p04_7/scl1 p05_1/an9/alarm1/sot2 *3 p05_2/an10/sck2 p05_3/an11/tin3/wot p07_5/an21/int5/sck9_r p07_4/an20/int4 p07_3/an19/int3 p07_2/an18/int2 p07_1/an17/int1 p07_0/an16/int0/nmi vss p06_7/an7/ppg7 p06_6/an6/ppg6 p06_5/an5/ppg5 p06_4/an4/ppg4 p06_3/an3/ppg3 p06_2/an2/ppg2 p06_1/an1/ppg1 p06_0/an0/ppg0 avss avrl/avrh2 *4 avrh avcc p02_5/a21/ttg9/ttg1/in1/adtg_r p05_7/an15/int5_r p05_6/an14/int4_r p05_5/an13/int0_r/nmi_r p05_4/an12/tot3/int2_r p05_0/an8/alarm0/sin2/int3_r1 *3 *2: tx0, rx0, tx1, rx1 are not available on mb96(f)34xayy or mb96(f)34xcyy mb96(f)34xywy : x0a, x1a mb96(f)34xysy : p04_0, p04_1 *1: tx1, rx1 are not available on mb96f345dyy or mb96f345fyy *3: alarm0, alarm1 are not available on mb96f345dyy or mb96f345fyy *4: avrh2 is not available on mb96f345dyy or mb96f345fyy www.datasheet.in
mb96340 series 10 fme-mb96340 rev 10 pin assignment of mb96(f)34x (fpt-100p-m20) remark: mb96(f)34x products are pin-compatible to f 2 mc-16lx family mb90340 series. 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 12 345 7 6 99 100 28 27 26 49 50 78 77 76 lqfp - 100 package code (mold) fpt-100p-m20 (fpt-100p-m20) p00_1ad01/int9/sot7_r p00_2/ad02/int10/sin7_r p00_3/ad03/int11/sck8_r p00_4/ad04/int12/sot8_r p00_5/ad05/int13/sin8_r p00_6/ad06/int14 p00_7/ad07/int15 p01_0/ad08/ckot1/tin1 p01_1/ad09/ckotx1/tot1 p01_2/ad10/int11_r/sin3 p01_3/ad11/sot3 p01_4/ad12/sck3 p01_5/ad13/int7_r/sin2_r p01_6/ad14/sot2_r p01_7/ad15/sck2_r p02_0/a16/ppg12 p02_1/a17/ppg13 p02_2/a18/ppg14 p02_3/a19/ppg15 p02_4/a20/ttg8/ttg0/in0 p02_5/a21/ttg9/ttg1/in1/adtg_r vcc vss x1 x0 md1 md2 p07_5/an21/int5/sck9_r p07_4/an20/int4 p07_3/an19/int3 p07_2/an18/int2 p07_1/an17/int1 p07_0/an16/int0/nmi vss p06_7/an7/ppg7 p06_6/an6/ppg6 p06_5/an5/ppg5 p06_4/an4/ppg4 p06_3/an3/ppg3 p06_2/an2/ppg2 p06_1/an1/ppg1 p06_0/an0/ppg0 avss avrl/avrh2 *4 avrh avcc p05_7/an15/int5_r p05_6/an14/int4_r p05_5/an13/int0_r/nmi_r p05_4/an12/tot3/int2_r p00_0/ad00/int8/sck7_r p10_1/tx0 *2 p10_0/rx0/int8_r *2 p09_7/out3/cs0 p09_6/out2/cs1 p09_5/out1/cs2 p09_4/out0/cs3 p09_3/ppg11/cs4 p09_2/ppg10/cs5 p09_1/ppg9/lbx p09_0/ppg8/ubx vss vcc p08_7/sck1 p08_6/sot1 p08_5/sin1/int1_r p08_4/sck0/int15_r p08_3/sot0/tot2 p08_2/sin0/tin2/int14_r p08_1/tot0/ckot0/int13_r p08_0/tin0/ckotx0/adtg/int12_r p07_7/an23/int7/sin9_r p07_6/an22/int6/sot9_r rstx md0 p02_6/a22/in2/ttg2/ttg10 p02_7/a23/in3/ttg3/ttg11 p03_0/ale/in4/ttg4/ttg12 p03_1/rdx/in5/ttg5/ttg13 p03_2/wrlx/wrx/int10_r p03_3/wrhx p03_4/hrq/out4 p03_5/hakx/out5 p03_6/rdy/out6 p03_7/eclk/out7 x0a/p04_0 * 1 x1a/p04_1 *1 vcc vss c p04_2/in6/rx1/int9_r/ttg6/ttg14 *2 p04_3/in7/tx1/ttg7/ttg15 *2 p04_4/sda0/frck0 p04_5/scl0/frck1 p04_6/sda1 p04_7/scl1 p05_0/an8/alarm0/sin2/int3_r1 *3 p05_1/an9/alarm1/sot2 *3 p05_2/an10/sck2 p05_3/an11/tin3/wot *2: tx0, rx0, tx1, rx1 are not available on mb96(f)34xayy or mb96(f)34xcyy mb96(f)34xywy : x0a, x1a mb96(f)34xysy : p04_0, p04_1 *1: tx1, rx1 are not available on mb96f345dyy or mb96f345fyy *3: alarm0, alarm1 are not available on mb96f345dyy or mb96f345fyy *4: avrh2 is not available on mb96f345dyy or mb96f345fyy www.datasheet.in
mb96340 series fme-mb96340 rev 10 11 pin function description pin function description (1 of 2) pin name feature description adn external bus external bus interface (multiplexed mode) address output and data input/output adtg adc a/d converter trigger input adtg_r adc relocated a/d converter trigger input alarmn alarm comparator alarm comparator n input ale external bus external bus address latch enable output an external bus external bus address output ann adc a/d converter channel n input av cc supply analog circuits power supply avrh adc a/d converter high reference voltage input avrh2 adc alternative a/d converter high reference voltage input avrl adc a/d converter low reference voltage input av ss supply analog circuits power supply c voltage regulator internally regulated power supply stabilization capacitor pin ckotn clock output function clock output function n output ckotxn clock output function clock output function n inverted output eclk external bus external bus clock output csn external bus external bus chip select n output frckn free running timer free running timer n input hakx external bus external bus hold acknowledge hrq external bus external bus hold request inn icu input capture unit n input intn external interrupt external interrupt n input intn_r external interrupt relocated external interrupt n input lbx external bus external bus interface lower byte select strobe output mdn core input pins for specifying the operating mode. nmi external interrupt non-maskable interrupt input nmi_r external interrupt relocated non-maskable interrupt input outn ocu output compare unit n waveform output www.datasheet.in
mb96340 series 12 fme-mb96340 rev 10 pxx_n gpio general purpose io ppgn ppg programmable pulse generator n output rdx external bus external bus interface read strobe output rdy external bus external bus interface external wait state request input rstx core reset input rxn can can interface n rx input sckn usart usart n serial clock input/output sckn_r usart relocated usart n serial clock input/output scln i2c i2c interface n clock i/o input/output sdan i2c i2c interface n serial data i/o input/output sinn usart usart n serial data input sinn_r usart relocated usart n serial data input sotn usart usart n serial data output sotn_r usart relocated usart n serial data output tinn reload timer reload timer n event input totn reload timer reload timer n output ttgn ppg programmable pulse generator n trigger input txn can can interface n tx output ubx external bus external bus interface upper byte select strobe output v cc supply power supply v ss supply power supply wot rtc real timer clock output wrhx external bus external bus high byte write strobe output wrlx/wrx external bus external bus low byte / word write strobe output x0 clock oscillator input x0a clock subclock oscillator input (only for devices with suf? "w") x1 clock oscillator output x1a clock subclock oscillator output (only for devices with suf? "w") pin function description (2 of 2) pin name feature description www.datasheet.in
mb96340 series fme-mb96340 rev 10 13 pin circuit type *1: please refer to i/o circuit type?for details on the i/o circuit types *2: devices with suf? ? *3: devices without suf? ? pin circuit types fpt-100p-m20 fpt-100p-m22 pin no. circuit type *1 pin no. circuit type *1 1-10 h 1-12 h 11,12 b *2 13, 14 b *2 11,12 h *3 13, 14 h *3 13,14 supply 15,16 supply 15 f 17 f 16,17 h 18,19 h 18-21 n 20-23 n 22-29 i 24-31 i 30 supply 32 supply 31-32 g 33-34 g 33 supply 35 supply 34 to 41 i 36 to 43 i 42 supply 44 supply 43 to 48 i 45 to 50 i 49 to 51 c 51 to 53 c 52 e 54 e 53 to 54 i 55 to 56 i 55 to 62 h 57 to 64 h 63, 64 supply 65, 66 supply 65 to 87 h 67 to 89 h 88,89 supply 90, 91 supply 90, 91 a 92, 93 a 92-100 h 94 to 100 h www.datasheet.in
mb96340 series 14 fme-mb96340 rev 10 i/o circuit type type circuit remarks a high-speed oscillation circuit: programmable between oscillation mode (ex- ternal crystal or resonator connected to x0/x1 pins) and fast external clock input (fci) mode (external clock connected to x0 pin) programmable feedback resistor = approx. 2 * 0.5 m ? . feedback resistor is grounded in the center when the oscillator is disabled or in fci mode b low-speed oscillation circuit: programmable feedback resistor = approx. 2*5m ? . feedback resistor is grounded in the center when the oscillator is disabled c mask rom and eva device: cmos hysteresis input pin flash device: cmos input pin e cmos hysteresis input pin pull-up resistor value: approx. 50 k ? x1 x0 r r mrfbe xout fci 0 1 fci or osc disable x1a x0a r r srfbe xout osc disable r hysteresis inputs r pull-up resistor hysteresis inputs www.datasheet.in
mb96340 series fme-mb96340 rev 10 15 f power supply input protection circuit g a/d converter ref+ (avrh/avrh2) power sup- ply input pin with protection circuit flash devices do not have a protection circuit against vcc for pins avrh/avrh2 devices without avrh reference switch do not have an analog switch for the avrl pin h cmos level output (programmable i ol =5ma, i oh = -5ma and i ol = 2ma, i oh = -2ma) 2 different cmos hysteresis inputs with input shutdown function * automotive input with input shutdown function ttl input with input shutdown function * programmable pull-up resistor: 50k ? approx. note: mb96f345dyy or mb96f345fyy: only automotive input and cmos hyster- esis input (0.7/0.3) are supported type circuit remarks ane avr ane pout pull-up control nout r hysteresis input automotive input ttl input hysteresis input standby control for input shutdown standby control for input shutdown standby control for input shutdown standby control for input shutdown www.datasheet.in
mb96340 series 16 fme-mb96340 rev 10 i cmos level output (programmable i ol =5ma, i oh = -5ma and i ol = 2ma, i oh = -2ma) 2 different cmos hysteresis inputs with input shutdown function * automotive input with input shutdown function ttl input with input shutdown function * programmable pull-up resistor: 50k ? approx. analog input note: mb96f345dyy or mb96f345fyy: only automotive input and cmos hyster- esis input (0.7/0.3) are supported n cmos level output (i ol = 3ma, i oh = -3ma) 2 different cmos hysteresis inputs with input shutdown function * automotive input with input shutdown function ttl input with input shutdown function * programmable pull-up resistor: 50k ? approx. *1: n-channel transistor has slew rate control ac- cording to i 2 c spec, irrespective of usage note: mb96f345dyy or mb96f345fyy: only automotive input and cmos hyster- esis input (0.7/0.3) are supported type circuit remarks r hysteresis input hysteresis input standby control for input shutdown standby control for input shutdown standby control for input shutdown standby control for input shutdown pull-up control pout nout automotive input ttl input analog input pout pull-up control nout *1 r hysteresis input automotive input ttl input hysteresis input standby control for input shutdown standby control for input shutdown standby control for input shutdown standby control for input shutdown www.datasheet.in
mb96340 series fme-mb96340 rev 10 17 memory map mb96v300b mb96(f)34x ff:ffff h emulation rom user rom / external bus *4 de:0000 h external bus external bus 10:0000 h 0f:e000 h boot-rom boot-rom reserved 0f:0000 h reserved 0e:0000 h data flash / reserved *4 external ram 0c:0000 h reserved 02:0000 h internal ram bank 1 reserved ramend1 *2 internal ram bank 1 ram availability de- pending on the device ramstart1 2 01:0000 h reserved rom/ram mirror rom/ram mirror 00:8000 h internal ram bank 0 internal ram bank 0 ramstart0 *2 reserved ramstart0 *3 external bus external bus end address *2 00:0c00 h external bus peripherals peripherals 00:0380 h 00:0180 h gpr *1 gpr *1 00:0100 h dma dma 00:00f0 h external bus external bus 00:0000 h peripheral peripheral *1: unused gpr banks can be used as ram area *2: for external bus end address and ramstart/end addresses, please refer to the table on the next page. *3: for eva device, ramstart0 depends on the con?uration of the emulated device. *4: for details about user rom area or data flash area, see the user rom memory map for flash devices and user rom memory map for mask rom devices on the following pages. the external bus area and dma area are only available if the device contains the corresponding resource. the available ram and rom area depends on the device. www.datasheet.in
mb96340 series 18 fme-mb96340 rev 10 ramstart/end and external bus end addresses devices bank 0 ram size bank 1 ram size external bus end address ramstart0 ramstart1 ramend1 mb96(f)345 8kbyte - 00:21ff h 00:6240 h -- mb96(f)346, mb96f347 16kbyte - 00:21ff h 00:4240 h -- mb96f348 24kbyte - 00:21ff h 00:2240 h -- www.datasheet.in
mb96340 series fme-mb96340 rev 10 19 user rom memory map for flash devices mb96f345d mb96f345f alternative mode cpu address flash memory mode address flash size 160kbyte +64kbyte data flash ff:ffff h ff:0000 h 3f:ffff h 3f:0000 h s39 - 64k flash a fe:ffff h fe:0000 h 3e:ffff h 3e:0000 h s38 - 64k fd:ffff h fd:0000 h 3d:ffff h 3d:0000 h external bus fc:ffff h fc:0000 h 3c:ffff h 3c:0000 h fb:ffff h fb:0000 h 3b:ffff h 3b:0000 h fa:ffff h fa:0000 h 3a:ffff h 3a:0000 h f9:ffff h f9:0000 h 39:ffff h 39:0000 h f8:ffff h f8:0000 h 38:ffff h 38:0000 h f7:ffff h f7:0000 h 37:ffff h 37:0000 h f6:ffff h f6:0000 h 36:ffff h 36:0000 h f5:ffff h f5:0000 h 35:ffff h 35:0000 h f4:ffff h f4:0000 h 34:ffff h 34:0000 h f3:ffff h f3:0000 h 33:ffff h 33:0000 h f2:ffff h f2:0000 h 32:ffff h 32:0000 h f1:ffff h f1:0000 h 31:ffff h 31:0000 h f0:ffff h f0:0000 h 30:ffff h 30:0000 h e0:ffff h e0:0000 h df:ffff h df:8000 h reserved df:7fff h df:6000 h 1f:7fff h 1f:6000 h sa3 - 8k flash a df:5fff h df:4000 h 1f:5fff h 1f:4000 h sa2 - 8k df:3fff h df:2000 h 1f:3fff h 1f:2000 h sa1 - 8k df:1fff h df:0000 h 1f:1fff h 1f:0000 h sa0 - 8k *1 de:ffff h de:0000 h reserved 0e:ffff h 0e:ff00 h (0e:ffff h ) (0e:ff00 h ) sda0-256 *2 data flash a 0e:feff h 0e:0000 h reserved 0d:ffff h 0d:c000 h (0f:ffff h ) (0f:c000 h ) sda4-16k data flash a 0d:bfff h 0d:8000 h (0f:bfff h ) (0f:8000 h ) sda3-16k 0d:7fff h 0d:4000 h (0f:7fff h ) (0f:4000 h ) sda2-16k 0d:3fff h 0d:0000 h (0f:3fff h ) (0f:0000 h ) sda1-16k 0c:ffff h 0c:0000 h reserved *1: sector sa0 contains the rom con?uration block rcba at cpu address df:0000 h - df:007f h *2: sector sda0 contains the rom con?uration block rcbda at cpu address de:ff00 h - de:ff2f h www.datasheet.in
mb96340 series 20 fme-mb96340 rev 10 mb96f346y mb96f347y mb96f346r mb96f347r mb96f346a mb96f347a alternative mode cpu address flash memory mode address flash size 288kbyte flash size 416kbyte ff:ffff h ff:0000 h 3f:ffff h 3f:0000 h s39 - 64k s39 - 64k flash a fe:ffff h fe:0000 h 3e:ffff h 3e:0000 h s38 - 64k s38 - 64k fd:ffff h fd:0000 h 3d:ffff h 3d:0000 h s37 - 64k s37 - 64k fc:ffff h fc:0000 h 3c:ffff h 3c:0000 h s36 - 64k s36 - 64k fb:ffff h fb:0000 h 3b:ffff h 3b:0000 h external bus s35 - 64k fa:ffff h fa:0000 h 3a:ffff h 3a:0000 h s34 - 64k f9:ffff h f9:0000 h 39:ffff h 39:0000 h external bus f8:ffff h f8:0000 h 38:ffff h 38:0000 h f7:ffff h f7:0000 h 37:ffff h 37:0000 h f6:ffff h f6:0000 h 36:ffff h 36:0000 h f5:ffff h f5:0000 h 35:ffff h 35:0000 h f4:ffff h f4:0000 h 34:ffff h 34:0000 h f3:ffff h f3:0000 h 33:ffff h 33:0000 h f2:ffff h f2:0000 h 32:ffff h 32:0000 h f1:ffff h f1:0000 h 31:ffff h 31:0000 h f0:ffff h f0:0000 h 30:ffff h 30:0000 h e0:ffff h e0:0000 h df:ffff h df:8000 h reserved reserved df:7fff h df:6000 h 1f:7fff h 1f:6000 h sa3 - 8k sa3 - 8k flash a df:5fff h df:4000 h 1f:5fff h 1f:4000 h sa2 - 8k sa2 - 8k df:3fff h df:2000 h 1f:3fff h 1f:2000 h sa1 - 8k sa1 - 8k df:1fff h df:0000 h 1f:1fff h 1f:0000 h sa0 - 8k *1 sa0 - 8k *1 de:ffff h de:0000 h reserved reserved *1: sector sa0 contains the rom con?uration block rcba at cpu address df:0000 h - df:007f h www.datasheet.in
mb96340 series fme-mb96340 rev 10 21 mb96f348y mb96f348t mb96f348r mb96f348h mb96f348a mb96f348c alternative mode cpu address flash memory mode address flash size 544kbyte flash size 576kbyte ff:ffff h ff:0000 h 3f:ffff h 3f:0000 h s39 - 64k s39 - 64k fe:ffff h fe:0000 h 3e:ffff h 3e:0000 h s38 - 64k s38 - 64k flash a fd:ffff h fd:0000 h 3d:ffff h 3d:0000 h s37 - 64k s37 - 64k fc:ffff h fc:0000 h 3c:ffff h 3c:0000 h s36 - 64k s36 - 64k fb:ffff h fb:0000 h 3b:ffff h 3b:0000 h s35 - 64k s35 - 64k fa:ffff h fa:0000 h 3a:ffff h 3a:0000 h s34 - 64k s34 - 64k f9:ffff h f9:0000 h 39:ffff h 39:0000 h s33 - 64k s33 - 64k f8:ffff h f8:0000 h 38:ffff h 38:0000 h s32 - 64k s32 - 64k f7:ffff h f7:0000 h 37:ffff h 37:0000 h external bus external bus f6:ffff h f6:0000 h 36:ffff h 36:0000 h f5:ffff h f5:0000 h 35:ffff h 35:0000 h f4:ffff h f4:0000 h 34:ffff h 34:0000 h f3:ffff h f3:0000 h 33:ffff h 33:0000 h f2:ffff h f2:0000 h 32:ffff h 32:0000 h f1:ffff h f1:0000 h 31:ffff h 31:0000 h f0:ffff h f0:0000 h 30:ffff h 30:0000 h e0:ffff h e0:0000 h df:ffff h df:8000 h reserved reserved df:7fff h df:6000 h 1f:7fff h 1f:6000 h sa3 - 8k sa3 - 8k flash a df:5fff h df:4000 h 1f:5fff h 1f:4000 h sa2 - 8k sa2 - 8k df:3fff h df:2000 h 1f:3fff h 1f:2000 h sa1 - 8k sa1 - 8k df:1fff h df:0000 h 1f:1fff h 1f:0000 h sa0 - 8k *1 sa0 - 8k *1 de:ffff h de:8000 h reserved reserved de:7fff h de:6000 h 1e:7fff h 1e:6000 h sb3 - 8k flash b de:5fff h de:4000 h 1e:5fff h 1e:4000 h sb2 - 8k de:3fff h de:2000 h 1e:3fff h 1e:2000 h sb1 - 8k de:1fff h de:0000 h 1e:1fff h 1e:0000 h sb0 - 8k *2 *1: sector sa0 contains the rom con?uration block rcba at cpu address df:0000 h - df:007f h *2: sector sb0 contains the rom con?uration block rcbb at cpu address de:0000 h - de:002f h www.datasheet.in
mb96340 series 22 fme-mb96340 rev 10 user rom memory map for mask rom devices MB96345 mb96346 cpu address rom size 160kbyte rom size 288kbyte ff:ffff h ff:0000 h 128k rom 256k rom fe:ffff h fe:0000 h fd:ffff h fd:0000 h reserved fc:ffff h fc:0000 h fb:ffff h e0:0000 h external bus external bus df:ffff h df:8000 h reserved reserved df:7fff h df:0080 h 32k rom 32k rom df:007f h df:0000 h rom con?uration block rcb rom con?uration block rcb de:ffff h de:0000 h reserved reserved www.datasheet.in
mb96340 series fme-mb96340 rev 10 23 serial programming communication interface note: if a flash programmer and its software needs to use a handshaking pin, fujitsu suggests to the tool vendor to support at least port p00_1 on pin 76/78. if handshaking is used by the tool but p00_1 is not available in customers application, fujitsu suggests to the customer to check the tool manual or to contact the tool vendor for alternative handshaking pins. usart pins for flash serial programming (md[2:0] = 010, serial communication mode) mb96f34x pin number pin number usart number normal function lqfp-100 qfp-100 57 59 usart0 sin0 58 60 sot0 59 61 sck0 60 62 usart1 sin1 61 63 sot1 62 64 sck1 22 24 usart2 sin2 23 25 sot2 24 26 sck2 85 87 usart3 sin3 86 88 sot3 87 89 sck3 www.datasheet.in
mb96340 series 24 fme-mb96340 rev 10 i/o map i/o map mb96(f)34x (1 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access 000000 h i/o port p00 - port data register pdr00 r/w 000001 h i/o port p01 - port data register pdr01 r/w 000002 h i/o port p02 - port data register pdr02 r/w 000003 h i/o port p03 - port data register pdr03 r/w 000004 h i/o port p04 - port data register pdr04 r/w 000005 h i/o port p05 - port data register pdr05 r/w 000006 h i/o port p06 - port data register pdr06 r/w 000007 h i/o port p07 - port data register pdr07 r/w 000008 h i/o port p08 - port data register pdr08 r/w 000009 h i/o port p09 - port data register pdr09 r/w 00000a h i/o port p10 - port data register pdr10 r/w 00000b h - 000017 h reserved - 000018 h adc0 - control status register low adcsl adcs r/w 000019 h adc0 - control status register high adcsh r/w 00001a h adc0 - data register low adcrl adcr r 00001b h adc0 - data register high adcrh r 00001c h adc0 - setting register adsr r/w 00001d h adc0 - setting register r/w 00001e h adc0 - extended con?uration register adecr r/w 00001f h reserved - 000020 h frt0 - data register of free-running timer tcdt0 r/w 000021 h frt0 - data register of free-running timer r/w 000022 h frt0 - control status register of free-running timer low tccsl0 tccs0 r/w 000023 h frt0 - control status register of free-running timer high tccsh0 r/w 000024 h frt1 - data register of free-running timer tcdt1 r/w 000025 h frt1 - data register of free-running timer r/w www.datasheet.in
mb96340 series fme-mb96340 rev 10 25 000026 h frt1 - control status register of free-running timer low tccsl1 tccs1 r/w 000027 h frt1 - control status register of free-running timer high tccsh1 r/w 000028 h ocu0 - output compare control status ocs0 r/w 000029 h ocu1 - output compare control status ocs1 r/w 00002a h ocu0 - compare register occp0 r/w 00002b h ocu0 - compare register r/w 00002c h ocu1 - compare register occp1 r/w 00002d h ocu1 - compare register r/w 00002e h ocu2 - output compare control status ocs2 r/w 00002f h ocu3 - output compare control status ocs3 r/w 000030 h ocu2 - compare register occp2 r/w 000031 h ocu2 - compare register r/w 000032 h ocu3 - compare register occp3 r/w 000033 h ocu3 - compare register r/w 000034 h ocu4 - output compare control status ocs4 r/w 000035 h ocu5 - output compare control status ocs5 r/w 000036 h ocu4 - compare register occp4 r/w 000037 h ocu4 - compare register r/w 000038 h ocu5 - compare register occp5 r/w 000039 h ocu5 - compare register r/w 00003a h ocu6 - output compare control status ocs6 r/w 00003b h ocu7 - output compare control status ocs7 r/w 00003c h ocu6 - compare register occp6 r/w 00003d h ocu6 - compare register r/w 00003e h ocu7 - compare register occp7 r/w 00003f h ocu7 - compare register r/w 000040 h icu0/icu1 - control status register ics01 r/w 000041 h icu0/icu1 - edge register ice01 r/w 000042 h icu0 - capture register low ipcpl0 ipcp0 r i/o map mb96(f)34x (2 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 26 fme-mb96340 rev 10 000043 h icu0 - capture register high ipcph0 r 000044 h icu1 - capture register low ipcpl1 ipcp1 r 000045 h icu1 - capture register high ipcph1 r 000046 h icu2/icu3 - control status register ics23 r/w 000047 h icu2/icu3 - edge register ice23 r/w 000048 h icu2 - capture register low ipcpl2 ipcp2 r 000049 h icu2 - capture register high ipcph2 r 00004a h icu3 - capture register low ipcpl3 ipcp3 r 00004b h icu3 - capture register high ipcph3 r 00004c h icu4/icu5 - control status register ics45 r/w 00004d h icu4/icu5 - edge register ice45 r/w 00004e h icu4 - capture register low ipcpl4 ipcp4 r 00004f h icu4 - capture register high ipcph4 r 000050 h icu5 - capture register low ipcpl5 ipcp5 r 000051 h icu5 - capture register high ipcph5 r 000052 h icu6/icu7 - control status register ics67 r/w 000053 h icu6/icu7 - edge register ice67 r/w 000054 h icu6 - capture register low ipcpl6 ipcp6 r 000055 h icu6 - capture register high ipcph6 r 000056 h icu7 - capture register low ipcpl7 ipcp7 r 000057 h icu7 - capture register high ipcph7 r 000058 h extint0 - external interrupt enable register enir0 r/w 000059 h extint0 - external interrupt interrupt request register eirr0 r/w 00005a h extint0 - external interrupt level select low elvrl0 elvr0 r/w 00005b h extint0 - external interrupt level select high elvrh0 r/w 00005c h extint1 - external interrupt enable register enir1 r/w 00005d h extint1 - external interrupt interrupt request register eirr1 r/w 00005e h extint1 - external interrupt level select low elvrl1 elvr1 r/w 00005f h extint1 - external interrupt level select high elvrh1 r/w i/o map mb96(f)34x (3 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 27 000060 h rlt0 - timer control status register low tmcsrl0 tmcsr0 r/w 000061 h rlt0 - timer control status register high tmcsrh0 r/w 000062 h rlt0 - reload register - for writing tmrlr0 w 000062 h rlt0 - reload register - for reading tmr0 r 000063 h rlt0 - reload register - for writing w 000063 h rlt0 - reload register - for reading r 000064 h rlt1 - timer control status register low tmcsrl1 tmcsr1 r/w 000065 h rlt1 - timer control status register high tmcsrh1 r/w 000066 h rlt1 - reload register - for writing tmrlr1 w 000066 h rlt1 - reload register - for reading tmr1 r 000067 h rlt1 - reload register - for writing w 000067 h rlt1 - reload register - for reading r 000068 h rlt2 - timer control status register low tmcsrl2 tmcsr2 r/w 000069 h rlt2 - timer control status register high tmcsrh2 r/w 00006a h rlt2 - reload register - for writing tmrlr2 w 00006a h rlt2 - reload register - for reading tmr2 r 00006b h rlt2 - reload register - for writing w 00006b h rlt2 - reload register - for reading r 00006c h rlt3 - timer control status register low tmcsrl3 tmcsr3 r/w 00006d h rlt3 - timer control status register high tmcsrh3 r/w 00006e h rlt3 - reload register - for writing tmrlr3 w 00006e h rlt3 - reload register - for reading tmr3 r 00006f h rlt3 - reload register - for writing w 00006f h rlt3 - reload register - for reading r 000070 h rlt6 - timer control status register low (dedic. rlt for ppg) tmcsrl6 tmcsr6 r/w 000071 h rlt6 - timer control status register high (dedic. rlt for ppg) tmcsrh6 r/w 000072 h rlt6 - reload register (dedic. rlt for ppg) - for writing tmrlr6 w i/o map mb96(f)34x (4 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 28 fme-mb96340 rev 10 000072 h rlt6 - reload register (dedic. rlt for ppg) - for reading tmr6 r 000073 h rlt6 - reload register (dedic. rlt for ppg) - for writing w 000073 h rlt6 - reload register (dedic. rlt for ppg) - for reading r 000074 h ppg3-ppg0 - general control register 1 low gcn1l0 gcn10 r/w 000075 h ppg3-ppg0 - general control register 1 high gcn1h0 r/w 000076 h ppg3-ppg0 - general control register 2 low gcn2l0 gcn20 r/w 000077 h ppg3-ppg0 - general control register 2 high gcn2h0 r/w 000078 h ppg0 - timer register ptmr0 r 000079 h ppg0 - timer register r 00007a h ppg0 - period setting register pcsr0 w 00007b h ppg0 - period setting register w 00007c h ppg0 - duty cycle register pdut0 w 00007d h ppg0 - duty cycle register w 00007e h ppg0 - control status register low pcnl0 pcn0 r/w 00007f h ppg0 - control status register high pcnh0 r/w 000080 h ppg1 - timer register ptmr1 r 000081 h ppg1 - timer register r 000082 h ppg1 - period setting register pcsr1 w 000083 h ppg1 - period setting register w 000084 h ppg1 - duty cycle register pdut1 w 000085 h ppg1 - duty cycle register w 000086 h ppg1 - control status register low pcnl1 pcn1 r/w 000087 h ppg1 - control status register high pcnh1 r/w 000088 h ppg2 - timer register ptmr2 r 000089 h ppg2 - timer register r 00008a h ppg2 - period setting register pcsr2 w 00008b h ppg2 - period setting register w 00008c h ppg2 - duty cycle register pdut2 w i/o map mb96(f)34x (5 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 29 00008d h ppg2 - duty cycle register w 00008e h ppg2 - control status register low pcnl2 pcn2 r/w 00008f h ppg2 - control status register high pcnh2 r/w 000090 h ppg3 - timer register ptmr3 r 000091 h ppg3 - timer register r 000092 h ppg3 - period setting register pcsr3 w 000093 h ppg3 - period setting register w 000094 h ppg3 - duty cycle register pdut3 w 000095 h ppg3 - duty cycle register w 000096 h ppg3 - control status register low pcnl3 pcn3 r/w 000097 h ppg3 - control status register high pcnh3 r/w 000098 h ppg7-ppg4 - general control register 1 low gcn1l1 gcn11 r/w 000099 h ppg7-ppg4 - general control register 1 high gcn1h1 r/w 00009a h ppg7-ppg4 - general control register 2 low gcn2l1 gcn21 r/w 00009b h ppg7-ppg4 - general control register 2 high gcn2h1 r/w 00009c h ppg4 - timer register ptmr4 r 00009d h ppg4 - timer register r 00009e h ppg4 - period setting register pcsr4 w 00009f h ppg4 - period setting register w 0000a0 h ppg4 - duty cycle register pdut4 w 0000a1 h ppg4 - duty cycle register w 0000a2 h ppg4 - control status register low pcnl4 pcn4 r/w 0000a3 h ppg4 - control status register high pcnh4 r/w 0000a4 h ppg5 - timer register ptmr5 r 0000a5 h ppg5 - timer register r 0000a6 h ppg5 - period setting register pcsr5 w 0000a7 h ppg5 - period setting register w 0000a8 h ppg5 - duty cycle register pdut5 w 0000a9 h ppg5 - duty cycle register w 0000aa h ppg5 - control status register low pcnl5 pcn5 r/w i/o map mb96(f)34x (6 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 30 fme-mb96340 rev 10 0000ab h ppg5 - control status register high pcnh5 r/w 0000ac h i2c0 - bus status register ibsr0 r 0000ad h i2c0 - bus control register ibcr0 r/w 0000ae h i2c0 - ten bit slave address register low itbal0 itba0 r/w 0000af h i2c0 - ten bit slave address register high itbah0 r/w 0000b0 h i2c0 - ten bit address mask register low itmkl0 itmk0 r/w 0000b1 h i2c0 - ten bit address mask register high itmkh0 r/w 0000b2 h i2c0 - seven bit slave address register isba0 r/w 0000b3 h i2c0 - seven bit address mask register ismk0 r/w 0000b4 h i2c0 - data register idar0 r/w 0000b5 h i2c0 - clock control register iccr0 r/w 0000b6 h i2c1 - bus status register ibsr1 r 0000b7 h i2c1 - bus control register ibcr1 r/w 0000b8 h i2c1 - ten bit slave address register low itbal1 itba1 r/w 0000b9 h i2c1 - ten bit slave address register high itbah1 r/w 0000ba h i2c1 - ten bit address mask register low itmkl1 itmk1 r/w 0000bb h i2c1 - ten bit address mask register high itmkh1 r/w 0000bc h i2c1 - seven bit slave address register isba1 r/w 0000bd h i2c1 - seven bit address mask register ismk1 r/w 0000be h i2c1 - data register idar1 r/w 0000bf h i2c1 - clock control register iccr1 r/w 0000c0 h usart0 - serial mode register smr0 r/w 0000c1 h usart0 - serial control register scr0 r/w 0000c2 h usart0 - tx register tdr0 w 0000c2 h usart0 - rx register rdr0 r 0000c3 h usart0 - serial status ssr0 r/w 0000c4 h usart0 - control/com. register eccr0 r/w 0000c5 h usart0 - ext. status register escr0 r/w 0000c6 h usart0 - baud rate generator register low bgrl0 bgr0 r/w 0000c7 h usart0 - baud rate generator register high bgrh0 r/w i/o map mb96(f)34x (7 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 31 0000c8 h usart0 - extended serial interrupt register esir0 r/w 0000c9 h reserved - 0000ca h usart1 - serial mode register smr1 r/w 0000cb h usart1 - serial control register scr1 r/w 0000cc h usart1 - tx register tdr1 w 0000cc h usart1 - rx register rdr1 r 0000cd h usart1 - serial status ssr1 r/w 0000ce h usart1 - control/com. register eccr1 r/w 0000cf h usart1 - ext. status register escr1 r/w 0000d0 h usart1 - baud rate generator register low bgrl1 bgr1 r/w 0000d1 h usart1 - baud rate generator register high bgrh1 r/w 0000d2 h usart1 - extended serial interrupt register esir1 r/w 0000d3 h reserved - 0000d4 h usart2 - serial mode register smr2 r/w 0000d5 h usart2 - serial control register scr2 r/w 0000d6 h usart2 - tx register tdr2 w 0000d6 h usart2 - rx register rdr2 r 0000d7 h usart2 - serial status ssr2 r/w 0000d8 h usart2 - control/com. register eccr2 r/w 0000d9 h usart2 - ext. status register escr2 r/w 0000da h usart2 - baud rate generator register low bgrl2 bgr2 r/w 0000db h usart2 - baud rate generator register high bgrh2 r/w 0000dc h usart2 - extended serial interrupt register esir2 r/w 0000dd h reserved - 0000de h usart3 - serial mode register smr3 r/w 0000df h usart3 - serial control register scr3 r/w 0000e0 h usart3 - tx register tdr3 w 0000e0 h usart3 - rx register rdr3 r 0000e1 h usart3 - serial status ssr3 r/w 0000e2 h usart3 - control/com. register eccr3 r/w i/o map mb96(f)34x (8 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 32 fme-mb96340 rev 10 0000e3 h usart3 - ext. status register escr3 r/w 0000e4 h usart3 - baud rate generator register low bgrl3 bgr3 r/w 0000e5 h usart3 - baud rate generator register high bgrh3 r/w 0000e6 h usart3 - extended serial interrupt register esir3 r/w 0000e7 h - 0000ef h reserved - 0000f0 h - 0000ff h external bus area extbus0 r/w 000100 h dma0 - buffer address pointer low byte bapl0 r/w 000101 h dma0 - buffer address pointer middle byte bapm0 r/w 000102 h dma0 - buffer address pointer high byte baph0 r/w 000103 h dma0 - dma control register dmacs0 r/w 000104 h dma0 - i/o register address pointer low byte ioal0 ioa0 r/w 000105 h dma0 - i/o register address pointer high byte ioah0 r/w 000106 h dma0 - data counter low byte dctl0 dct0 r/w 000107 h dma0 - data counter high byte dcth0 r/w 000108 h dma1 - buffer address pointer low byte bapl1 r/w 000109 h dma1 - buffer address pointer middle byte bapm1 r/w 00010a h dma1 - buffer address pointer high byte baph1 r/w 00010b h dma1 - dma control register dmacs1 r/w 00010c h dma1 - i/o register address pointer low byte ioal1 ioa1 r/w 00010d h dma1 - i/o register address pointer high byte ioah1 r/w 00010e h dma1 - data counter low byte dctl1 dct1 r/w 00010f h dma1 - data counter high byte dcth1 r/w 000110 h dma2 - buffer address pointer low byte bapl2 r/w 000111 h dma2 - buffer address pointer middle byte bapm2 r/w 000112 h dma2 - buffer address pointer high byte baph2 r/w 000113 h dma2 - dma control register dmacs2 r/w 000114 h dma2 - i/o register address pointer low byte ioal2 ioa2 r/w 000115 h dma2 - i/o register address pointer high byte ioah2 r/w 000116 h dma2 - data counter low byte dctl2 dct2 r/w i/o map mb96(f)34x (9 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 33 000117 h dma2 - data counter high byte dcth2 r/w 000118 h dma3 - buffer address pointer low byte bapl3 r/w 000119 h dma3 - buffer address pointer middle byte bapm3 r/w 00011a h dma3 - buffer address pointer high byte baph3 r/w 00011b h dma3 - dma control register dmacs3 r/w 00011c h dma3 - i/o register address pointer low byte ioal3 ioa3 r/w 00011d h dma3 - i/o register address pointer high byte ioah3 r/w 00011e h dma3 - data counter low byte dctl3 dct3 r/w 00011f h dma3 - data counter high byte dcth3 r/w 000120 h dma4 - buffer address pointer low byte bapl4 r/w 000121 h dma4 - buffer address pointer middle byte bapm4 r/w 000122 h dma4 - buffer address pointer high byte baph4 r/w 000123 h dma4 - dma control register dmacs4 r/w 000124 h dma4 - i/o register address pointer low byte ioal4 ioa4 r/w 000125 h dma4 - i/o register address pointer high byte ioah4 r/w 000126 h dma4 - data counter low byte dctl4 dct4 r/w 000127 h dma4 - data counter high byte dcth4 r/w 000128 h dma5 - buffer address pointer low byte bapl5 r/w 000129 h dma5 - buffer address pointer middle byte bapm5 r/w 00012a h dma5 - buffer address pointer high byte baph5 r/w 00012b h dma5 - dma control register dmacs5 r/w 00012c h dma5 - i/o register address pointer low byte ioal5 ioa5 r/w 00012d h dma5 - i/o register address pointer high byte ioah5 r/w 00012e h dma5 - data counter low byte dctl5 dct5 r/w 00012f h dma5 - data counter high byte dcth5 r/w 000130 h - 00017f h reserved - 000180 h - 00037f h cpu - general purpose registers (ram access) gpr_ram r/w 000380 h dma0 - interrupt select disel0 r/w 000381 h dma1 - interrupt select disel1 r/w i/o map mb96(f)34x (10 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 34 fme-mb96340 rev 10 000382 h dma2 - interrupt select disel2 r/w 000383 h dma3 - interrupt select disel3 r/w 000384 h dma4 - interrupt select disel4 r/w 000385 h dma5 - interrupt select disel5 r/w 000386 h - 00038f h reserved - 000390 h dma - status register low byte dsrl dsr r/w 000391 h dma - status register high byte dsrh r/w 000392 h dma - stop status register low byte dssrl dssr r/w 000393 h dma - stop status register high byte dssrh r/w 000394 h dma - enable register low byte derl der r/w 000395 h dma - enable register high byte derh r/w 000396 h - 00039f h reserved - 0003a0 h interrupt level register ilr icr r/w 0003a1 h interrupt index register idx r/w 0003a2 h interrupt vector table base register low tbrl tbr r/w 0003a3 h interrupt vector table base register high tbrh r/w 0003a4 h delayed interrupt register dirr r/w 0003a5 h non maskable interrupt register nmi r/w 0003a6 h - 0003ab h reserved - 0003ac h edsu communication interrupt selection low edsu2l edsu2 r/w 0003ad h edsu communication interrupt selection high edsu2h r/w 0003ae h rom mirror control register romm r/w 0003af h edsu con?uration register edsu r/w 0003b0 h memory patch control/status register ch 0/1 pfcs0 r/w 0003b1 h memory patch control/status register ch 0/1 r/w 0003b2 h memory patch control/status register ch 2/3 pfcs1 r/w 0003b3 h memory patch control/status register ch 2/3 r/w 0003b4 h memory patch control/status register ch 4/5 pfcs2 r/w i/o map mb96(f)34x (11 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 35 0003b5 h memory patch control/status register ch 4/5 r/w 0003b6 h memory patch control/status register ch 6/7 pfcs3 r/w 0003b7 h memory patch control/status register ch 6/7 r/w 0003b8 h memory patch function - patch address 0 low pfal0 r/w 0003b9 h memory patch function - patch address 0 middle pfam0 r/w 0003ba h memory patch function - patch address 0 high pfah0 r/w 0003bb h memory patch function - patch address 1 low pfal1 r/w 0003bc h memory patch function - patch address 1 middle pfam1 r/w 0003bd h memory patch function - patch address 1 high pfah1 r/w 0003be h memory patch function - patch address 2 low pfal2 r/w 0003bf h memory patch function - patch address 2 middle pfam2 r/w 0003c0 h memory patch function - patch address 2 high pfah2 r/w 0003c1 h memory patch function - patch address 3 low pfal3 r/w 0003c2 h memory patch function - patch address 3 middle pfam3 r/w 0003c3 h memory patch function - patch address 3 high pfah3 r/w 0003c4 h memory patch function - patch address 4 low pfal4 r/w 0003c5 h memory patch function - patch address 4 middle pfam4 r/w 0003c6 h memory patch function - patch address 4 high pfah4 r/w 0003c7 h memory patch function - patch address 5 low pfal5 r/w 0003c8 h memory patch function - patch address 5 middle pfam5 r/w 0003c9 h memory patch function - patch address 5 high pfah5 r/w 0003ca h memory patch function - patch address 6 low pfal6 r/w 0003cb h memory patch function - patch address 6 middle pfam6 r/w 0003cc h memory patch function - patch address 6 high pfah6 r/w 0003cd h memory patch function - patch address 7 low pfal7 r/w 0003ce h memory patch function - patch address 7 middle pfam7 r/w 0003cf h memory patch function - patch address 7 high pfah7 r/w 0003d0 h memory patch function - patch data 0 low pfdl0 pfd0 r/w 0003d1 h memory patch function - patch data 0 high pfdh0 r/w 0003d2 h memory patch function - patch data 1 low pfdl1 pfd1 r/w i/o map mb96(f)34x (12 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 36 fme-mb96340 rev 10 0003d3 h memory patch function - patch data 1 high pfdh1 r/w 0003d4 h memory patch function - patch data 2 low pfdl2 pfd2 r/w 0003d5 h memory patch function - patch data 2 high pfdh2 r/w 0003d6 h memory patch function - patch data 3 low pfdl3 pfd3 r/w 0003d7 h memory patch function - patch data 3 high pfdh3 r/w 0003d8 h memory patch function - patch data 4 low pfdl4 pfd4 r/w 0003d9 h memory patch function - patch data 4 high pfdh4 r/w 0003da h memory patch function - patch data 5 low pfdl5 pfd5 r/w 0003db h memory patch function - patch data 5 high pfdh5 r/w 0003dc h memory patch function - patch data 6 low pfdl6 pfd6 r/w 0003dd h memory patch function - patch data 6 high pfdh6 r/w 0003de h memory patch function - patch data 7 low pfdl7 pfd7 r/w 0003df h memory patch function - patch data 7 high pfdh7 r/w 0003e0 h data flash control and status register a dfcsa r/w 0003e1 h data flash write command sequencer control register a dfwca r/w 0003e2 h data flash write command sequencer status reg- ister a dfwsa r/w 0003e3 h - 0003f0 h reserved - 0003f1 h memory control status register a mcsra r/w 0003f2 h memory timing con?uration register a low mtcral mtcra r/w 0003f3 h memory timing con?uration register a high mtcrah r/w 0003f4 h reserved - 0003f5 h memory control status register b mcsrb r/w 0003f6 h memory timing con?uration register b low mtcrbl mtcrb r/w 0003f7 h memory timing con?uration register b high mtcrbh r/w 0003f8 h flash memory write control register 0 fmwc0 r/w 0003f9 h flash memory write control register 1 fmwc1 r/w 0003fa h flash memory write control register 2 fmwc2 r/w 0003fb h flash memory write control register 3 fmwc3 r/w i/o map mb96(f)34x (13 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 37 0003fc h flash memory write control register 4 fmwc4 r/w 0003fd h flash memory write control register 5 fmwc5 r/w 0003fe h - 0003ff h reserved - 000400 h standby mode control register smcr r/w 000401 h clock select register cksr r/w 000402 h clock stabilization select register ckssr r/w 000403 h clock monitor register ckmr r 000404 h clock frequency control register low ckfcrl ckfcr r/w 000405 h clock frequency control register high ckfcrh r/w 000406 h pll control register low pllcrl pllcr r/w 000407 h pll control register high pllcrh r/w 000408 h rc clock timer control register rctcr r/w 000409 h main clock timer control register mctcr r/w 00040a h sub clock timer control register sctcr r/w 00040b h reset cause and clock status register with clear function rccsrc r 00040c h reset con?uration register rcr r/w 00040d h reset cause and clock status register rccsr r 00040e h watch dog timer con?uration register wdtc r/w 00040f h watch dog timer clear pattern register wdtcp w 000410 h - 000414 h reserved - 000415 h clock output activation register coar r/w 000416 h clock output con?uration register 0 cocr0 r/w 000417 h clock output con?uration register 1 cocr1 r/w 000418 h clock modulator control register cmcr r/w 000419 h reserved - 00041a h clock modulator parameter register low cmprl cmpr r/w 00041b h clock modulator parameter register high cmprh r/w i/o map mb96(f)34x (14 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 38 fme-mb96340 rev 10 00041c h - 00042b h reserved - 00042c h voltage regulator control register vrcr r/w 00042d h clock input and lvd control register cilcr r/w 00042e h - 00042f h reserved - 000430 h i/o port p00 - data direction register ddr00 r/w 000431 h i/o port p01 - data direction register ddr01 r/w 000432 h i/o port p02 - data direction register ddr02 r/w 000433 h i/o port p03 - data direction register ddr03 r/w 000434 h i/o port p04 - data direction register ddr04 r/w 000435 h i/o port p05 - data direction register ddr05 r/w 000436 h i/o port p06 - data direction register ddr06 r/w 000437 h i/o port p07 - data direction register ddr07 r/w 000438 h i/o port p08 - data direction register ddr08 r/w 000439 h i/o port p09 - data direction register ddr09 r/w 00043a h i/o port p10 - data direction register ddr10 r/w 00043b h - 000443 h reserved - 000444 h i/o port p00 - port input enable register pier00 r/w 000445 h i/o port p01 - port input enable register pier01 r/w 000446 h i/o port p02 - port input enable register pier02 r/w 000447 h i/o port p03 - port input enable register pier03 r/w 000448 h i/o port p04 - port input enable register pier04 r/w 000449 h i/o port p05 - port input enable register pier05 r/w 00044a h i/o port p06 - port input enable register pier06 r/w 00044b h i/o port p07 - port input enable register pier07 r/w 00044c h i/o port p08 - port input enable register pier08 r/w 00044d h i/o port p09 - port input enable register pier09 r/w 00044e h i/o port p10 - port input enable register pier10 r/w i/o map mb96(f)34x (15 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 39 00044f h - 000457 h reserved - 000458 h i/o port p00 - port input level register pilr00 r/w 000459 h i/o port p01 - port input level register pilr01 r/w 00045a h i/o port p02 - port input level register pilr02 r/w 00045b h i/o port p03 - port input level register pilr03 r/w 00045c h i/o port p04 - port input level register pilr04 r/w 00045d h i/o port p05 - port input level register pilr05 r/w 00045e h i/o port p06 - port input level register pilr06 r/w 00045f h i/o port p07 - port input level register pilr07 r/w 000460 h i/o port p08 - port input level register pilr08 r/w 000461 h i/o port p09 - port input level register pilr09 r/w 000462 h i/o port p10 - port input level register pilr10 r/w 000463 h - 00046b h reserved - 00046c h i/o port p00 - extended port input level register epilr00 r/w 00046d h i/o port p01 - extended port input level register epilr01 r/w 00046e h i/o port p02 - extended port input level register epilr02 r/w 00046f h i/o port p03 - extended port input level register epilr03 r/w 000470 h i/o port p04 - extended port input level register epilr04 r/w 000471 h i/o port p05 - extended port input level register epilr05 r/w 000472 h i/o port p06 - extended port input level register epilr06 r/w 000473 h i/o port p07 - extended port input level register epilr07 r/w 000474 h i/o port p08 - extended port input level register epilr08 r/w 000475 h i/o port p09 - extended port input level register epilr09 r/w 000476 h i/o port p10 - extended port input level register epilr10 r/w 000477 h - 00047f h reserved - 000480 h i/o port p00 - port output drive register podr00 r/w 000481 h i/o port p01 - port output drive register podr01 r/w 000482 h i/o port p02 - port output drive register podr02 r/w i/o map mb96(f)34x (16 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 40 fme-mb96340 rev 10 000483 h i/o port p03 - port output drive register podr03 r/w 000484 h i/o port p04 - port output drive register podr04 r/w 000485 h i/o port p05 - port output drive register podr05 r/w 000486 h i/o port p06 - port output drive register podr06 r/w 000487 h i/o port p07 - port output drive register podr07 r/w 000488 h i/o port p08 - port output drive register podr08 r/w 000489 h i/o port p09 - port output drive register podr09 r/w 00048a h i/o port p10 - port output drive register podr10 r/w 00048b h - 0004a7 h reserved - 0004a8 h i/o port p00 - pull-up resistor control register pucr00 r/w 0004a9 h i/o port p01 - pull-up resistor control register pucr01 r/w 0004aa h i/o port p02 - pull-up resistor control register pucr02 r/w 0004ab h i/o port p03 - pull-up resistor control register pucr03 r/w 0004ac h i/o port p04 - pull-up resistor control register pucr04 r/w 0004ad h i/o port p05 - pull-up resistor control register pucr05 r/w 0004ae h i/o port p06 - pull-up resistor control register pucr06 r/w 0004af h i/o port p07 - pull-up resistor control register pucr07 r/w 0004b0 h i/o port p08 - pull-up resistor control register pucr08 r/w 0004b1 h i/o port p09 - pull-up resistor control register pucr09 r/w 0004b2 h i/o port p10 - pull-up resistor control register pucr10 r/w 0004b3 h - 0004bb h reserved - 0004bc h i/o port p00 - external pin state register epsr00 r 0004bd h i/o port p01 - external pin state register epsr01 r 0004be h i/o port p02 - external pin state register epsr02 r 0004bf h i/o port p03 - external pin state register epsr03 r 0004c0 h i/o port p04 - external pin state register epsr04 r 0004c1 h i/o port p05 - external pin state register epsr05 r 0004c2 h i/o port p06 - external pin state register epsr06 r 0004c3 h i/o port p07 - external pin state register epsr07 r i/o map mb96(f)34x (17 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 41 0004c4 h i/o port p08 - external pin state register epsr08 r 0004c5 h i/o port p09 - external pin state register epsr09 r 0004c6 h i/o port p10 - external pin state register epsr10 r 0004c7 h - 0004cf h reserved - 0004d0 h adc analog input enable register 0 ader0 r/w 0004d1 h adc analog input enable register 1 ader1 r/w 0004d2 h adc analog input enable register 2 ader2 r/w 0004d3 h adc analog input enable register 3 ader3 r/w 0004d4 h adc analog input enable register 4 ader4 r/w 0004d5 h reserved - 0004d6 h peripheral resource relocation register 0 prrr0 r/w 0004d7 h peripheral resource relocation register 1 prrr1 r/w 0004d8 h peripheral resource relocation register 2 prrr2 r/w 0004d9 h peripheral resource relocation register 3 prrr3 r/w 0004da h peripheral resource relocation register 4 prrr4 r/w 0004db h peripheral resource relocation register 5 prrr5 r/w 0004dc h peripheral resource relocation register 6 prrr6 r/w 0004dd h peripheral resource relocation register 7 prrr7 r/w 0004de h peripheral resource relocation register 8 prrr8 r/w 0004df h peripheral resource relocation register 9 prrr9 r/w 0004e0 h rtc - sub second register l wtbrl0 wtbr0 r/w 0004e1 h rtc - sub second register m wtbrh0 r/w 0004e2 h rtc - sub-second register h wtbr1 r/w 0004e3 h rtc - second register wtsr r/w 0004e4 h rtc - minutes wtmr r/w 0004e5 h rtc - hour wthr r/w 0004e6 h rtc - timer control extended register wtcer r/w 0004e7 h rtc - clock select register wtcksr r/w 0004e8 h rtc - timer control register low wtcrl wtcr r/w i/o map mb96(f)34x (18 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 42 fme-mb96340 rev 10 0004e9 h rtc - timer control register high wtcrh r/w 0004ea h cal - calibration unit control register cucr r/w 0004eb h reserved - 0004ec h cal - duration timer data register low cutdl cutd r/w 0004ed h cal - duration timer data register high cutdh r/w 0004ee h cal - calibration timer register 2 low cutr2l cutr2 r 0004ef h cal - calibration timer register 2 high cutr2h r 0004f0 h cal - calibration timer register 1 low cutr1l cutr1 r 0004f1 h cal - calibration timer register 1 high cutr1h r 0004f2 h - 0004f9 h reserved - 0004fa h rlt - timer input select (for cascading) tmisr r/w 0004fb h - 00053d h reserved - 00053e h usart7 - serial mode register smr7 r/w 00053f h usart7 - serial control register scr7 r/w 000540 h usart7 - serial tx register tdr7 w 000540 h usart7 - serial rx register rdr7 r 000541 h usart7 - serial status register ssr7 r/w 000542 h usart7 - ext. control/com. register eccr7 r/w 000543 h usart7 - ext. status com. register escr7 r/w 000544 h usart7 - baud rate generator register low bgrl7 bgr7 r/w 000545 h usart7 - baud rate generator register high bgrh7 r/w 000546 h usart7 - extended serial interrupt register esir7 r/w 000547 h reserved - 000548 h usart8 - serial mode register smr8 r/w 000549 h usart8 - serial control register scr8 r/w 00054a h usart8 - serial tx register tdr8 w 00054a h usart8 - serial rx register rdr8 r 00054b h usart8 - serial status register ssr8 r/w 00054c h usart8 - ext. control/com. register eccr8 r/w i/o map mb96(f)34x (19 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 43 00054d h usart8 - ext. status com. register escr8 r/w 00054e h usart8 - baud rate generator register low bgrl8 bgr8 r/w 00054f h usart8 - baud rate generator register high bgrh8 r/w 000550 h usart8 - extended serial interrupt register esir8 r/w 000551 h reserved - 000552 h usart9 - serial mode register smr9 r/w 000553 h usart9 - serial control register scr9 r/w 000554 h usart9 - serial tx register tdr9 w 000554 h usart9 - serial rx register rdr9 r 000555 h usart9 - serial status register ssr9 r/w 000556 h usart9 - ext. control/com. register eccr9 r/w 000557 h usart9 - ext. status com. register escr9 r/w 000558 h usart9 - baud rate generator register low bgrl9 bgr9 r/w 000559 h usart9 - baud rate generator register high bgrh9 r/w 00055a h usart9 - extended serial interrupt register esir9 r/w 00055b h - 00055f h reserved - 000560 h alarm0 - control status register acsr0 r/w 000561 h alarm0 - extended control status register aecsr0 r/w 000562 h alarm1 - control status register acsr1 r/w 000563 h alarm1 - extended control status register aecsr1 r/w 000564 h ppg6 - timer register ptmr6 r 000565 h ppg6 - timer register r 000566 h ppg6 - period setting register pcsr6 w 000567 h ppg6 - period setting register w 000568 h ppg6 - duty cycle register pdut6 w 000569 h ppg6 - duty cycle register w 00056a h ppg6 - control status register low pcnl6 pcn6 r/w 00056b h ppg6 - control status register high pcnh6 r/w 00056c h ppg7 - timer register ptmr7 r i/o map mb96(f)34x (20 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 44 fme-mb96340 rev 10 00056d h ppg7 - timer register r 00056e h ppg7 - period setting register pcsr7 w 00056f h ppg7 - period setting register w 000570 h ppg7 - duty cycle register pdut7 w 000571 h ppg7 - duty cycle register w 000572 h ppg7 - control status register low pcnl7 pcn7 r/w 000573 h ppg7 - control status register high pcnh7 r/w 000574 h ppg11-ppg8 - general control register 1 low gcn1l2 gcn12 r/w 000575 h ppg11-ppg8 - general control register 1 high gcn1h2 r/w 000576 h ppg11-ppg8 - general control register 2 low gcn2l2 gcn22 r/w 000577 h ppg11-ppg8 - general control register 2 high gcn2h2 r/w 000578 h ppg8 - timer register ptmr8 r 000579 h ppg8 - timer register r 00057a h ppg8 - period setting register pcsr8 w 00057b h ppg8 - period setting register w 00057c h ppg8 - duty cycle register pdut8 w 00057d h ppg8 - duty cycle register w 00057e h ppg8 - control status register low pcnl8 pcn8 r/w 00057f h ppg8 - control status register high pcnh8 r/w 000580 h ppg9 - timer register ptmr9 r 000581 h ppg9 - timer register r 000582 h ppg9 - period setting register pcsr9 w 000583 h ppg9 - period setting register w 000584 h ppg9 - duty cycle register pdut9 w 000585 h ppg9 - duty cycle register w 000586 h ppg9 - control status register low pcnl9 pcn9 r/w 000587 h ppg9 - control status register high pcnh9 r/w 000588 h ppg10 - timer register ptmr10 r 000589 h ppg10 - timer register r 00058a h ppg10 - period setting register pcsr10 w i/o map mb96(f)34x (21 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 45 00058b h ppg10 - period setting register w 00058c h ppg10 - duty cycle register pdut10 w 00058d h ppg10 - duty cycle register w 00058e h ppg10 - control status register low pcnl10 pcn10 r/w 00058f h ppg10 - control status register high pcnh10 r/w 000590 h ppg11 - timer register ptmr11 r 000591 h ppg11 - timer register r 000592 h ppg11 - period setting register pcsr11 w 000593 h ppg11 - period setting register w 000594 h ppg11 - duty cycle register pdut11 w 000595 h ppg11 - duty cycle register w 000596 h ppg11 - control status register low pcnl11 pcn11 r/w 000597 h ppg11 - control status register high pcnh11 r/w 000598 h ppg15-ppg12 - general control register 1 low gcn1l3 gcn13 r/w 000599 h ppg15-ppg12 - general control register 1 high gcn1h3 r/w 00059a h ppg15-ppg12 - general control register 2 low gcn2l3 gcn23 r/w 00059b h ppg15-ppg12 - general control register 2 high gcn2h3 r/w 00059c h ppg12 - timer register ptmr12 r 00059d h ppg12 - timer register r 00059e h ppg12 - period setting register pcsr12 w 00059f h ppg12 - period setting register w 0005a0 h ppg12 - duty cycle register pdut12 w 0005a1 h ppg12 - duty cycle register w 0005a2 h ppg12 - control status register low pcnl12 pcn12 r/w 0005a3 h ppg12 - control status register high pcnh12 r/w 0005a4 h ppg13 - timer register ptmr13 r 0005a5 h ppg13 - timer register r 0005a6 h ppg13 - period setting register pcsr13 w 0005a7 h ppg13 - period setting register w 0005a8 h ppg13 - duty cycle register pdut13 w i/o map mb96(f)34x (22 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 46 fme-mb96340 rev 10 0005a9 h ppg13 - duty cycle register w 0005aa h ppg13 - control status register low pcnl13 pcn13 r/w 0005ab h ppg13 - control status register high pcnh13 r/w 0005ac h ppg14 - timer register ptmr14 r 0005ad h ppg14 - timer register r 0005ae h ppg14 - period setting register pcsr14 w 0005af h ppg14 - period setting register w 0005b0 h ppg14 - duty cycle register pdut14 w 0005b1 h ppg14 - duty cycle register w 0005b2 h ppg14 - control status register low pcnl14 pcn14 r/w 0005b3 h ppg14 - control status register high pcnh14 r/w 0005b4 h ppg15 - timer register ptmr15 r 0005b5 h ppg15 - timer register r 0005b6 h ppg15 - period setting register pcsr15 w 0005b7 h ppg15 - period setting register w 0005b8 h ppg15 - duty cycle register pdut15 w 0005b9 h ppg15 - duty cycle register w 0005ba h ppg15 - control status register low pcnl15 pcn15 r/w 0005bb h ppg15 - control status register high pcnh15 r/w 0005bc h - 00065f h reserved - 000660 h peripheral resource relocation register 10 prrr10 r/w 000661 h peripheral resource relocation register 11 prrr11 r/w 000662 h peripheral resource relocation register 12 prrr12 r/w 000663 h peripheral resource relocation register 13 prrr13 w 000664 h - 0006df h reserved - 0006e0 h external bus - area con?uration register 0 low eacl0 eac0 r/w 0006e1 h external bus - area con?uration register 0 high each0 r/w 0006e2 h external bus - area con?uration register 1 low eacl1 eac1 r/w 0006e3 h external bus - area con?uration register 1 high each1 r/w i/o map mb96(f)34x (23 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 47 0006e4 h external bus - area con?uration register 2 low eacl2 eac2 r/w 0006e5 h external bus - area con?uration register 2 high each2 r/w 0006e6 h external bus - area con?uration register 3 low eacl3 eac3 r/w 0006e7 h external bus - area con?uration register 3 high each3 r/w 0006e8 h external bus - area con?uration register 4 low eacl4 eac4 r/w 0006e9 h external bus - area con?uration register 4 high each4 r/w 0006ea h external bus - area con?uration register 5 low eacl5 eac5 r/w 0006eb h external bus - area con?uration register 5 high each5 r/w 0006ec h external bus - area select register 2 eas2 r/w 0006ed h external bus - area select register 3 eas3 r/w 0006ee h external bus - area select register 4 eas4 r/w 0006ef h external bus - area select register 5 eas5 r/w 0006f0 h external bus - mode register ebm r/w 0006f1 h external bus - clock and function register ebcf r/w 0006f2 h external bus - address output enable register 0 ebae0 r/w 0006f3 h external bus - address output enable register 1 ebae1 r/w 0006f4 h external bus - address output enable register 2 ebae2 r/w 0006f5 h external bus - control signal register ebcs r/w 0006f6 h - 0006ff h reserved - 000700 h can0 - control register low ctrlrl0 ctrlr0 r/w 000701 h can0 - control register high (reserved) ctrlrh0 r 000702 h can0 - status register low statrl0 statr0 r/w 000703 h can0 - status register high (reserved) statrh0 r 000704 h can0 - error counter low (transmit) errcntl0 errcnt0 r 000705 h can0 - error counter high (receive) errcnth0 r 000706 h can0 - bit timing register low btrl0 btr0 r/w 000707 h can0 - bit timing register high btrh0 r/w 000708 h can0 - interrupt register low intrl0 intr0 r 000709 h can0 - interrupt register high intrh0 r i/o map mb96(f)34x (24 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 48 fme-mb96340 rev 10 00070a h can0 - test register low testrl0 testr0 r/w 00070b h can0 - test register high (reserved) testrh0 r 00070c h can0 - brp extension register low brperl0 brper0 r/w 00070d h can0 - brp extension register high (reserved) brperh0 r 00070e h - 00070f h reserved - 000710 h can0 - if1 command request register low if1creql0 if1creq0 r/w 000711 h can0 - if1 command request register high if1creqh0 r/w 000712 h can0 - if1 command mask register low if1cmskl0 if1cmsk0 r/w 000713 h can0 - if1 command mask register high (re- served) if1cmskh0 r 000714 h can0 - if1 mask 1 register low if1msk1l0 if1msk10 r/w 000715 h can0 - if1 mask 1 register high if1msk1h0 r/w 000716 h can0 - if1 mask 2 register low if1msk2l0 if1msk20 r/w 000717 h can0 - if1 mask 2 register high if1msk2h0 r/w 000718 h can0 - if1 arbitration 1 register low if1arb1l0 if1arb10 r/w 000719 h can0 - if1 arbitration 1 register high if1arb1h0 r/w 00071a h can0 - if1 arbitration 2 register low if1arb2l0 if1arb20 r/w 00071b h can0 - if1 arbitration 2 register high if1arb2h0 r/w 00071c h can0 - if1 message control register low if1mctrl0 if1mctr0 r/w 00071d h can0 - if1 message control register high if1mctrh0 r/w 00071e h can0 - if1 data a1 low if1dta1l0 if1dta10 r/w 00071f h can0 - if1 data a1 high if1dta1h0 r/w 000720 h can0 - if1 data a2 low if1dta2l0 if1dta20 r/w 000721 h can0 - if1 data a2 high if1dta2h0 r/w 000722 h can0 - if1 data b1 low if1dtb1l0 if1dtb10 r/w 000723 h can0 - if1 data b1 high if1dtb1h0 r/w 000724 h can0 - if1 data b2 low if1dtb2l0 if1dtb20 r/w 000725 h can0 - if1 data b2 high if1dtb2h0 r/w 000726 h - 00073f h reserved - i/o map mb96(f)34x (25 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 49 000740 h can0 - if2 command request register low if2creql0 if2creq0 r/w 000741 h can0 - if2 command request register high if2creqh0 r/w 000742 h can0 - if2 command mask register low if2cmskl0 if2cmsk0 r/w 000743 h can0 - if2 command mask register high (re- served) if2cmskh0 r 000744 h can0 - if2 mask 1 register low if2msk1l0 if2msk10 r/w 000745 h can0 - if2 mask 1 register high if2msk1h0 r/w 000746 h can0 - if2 mask 2 register low if2msk2l0 if2msk20 r/w 000747 h can0 - if2 mask 2 register high if2msk2h0 r/w 000748 h can0 - if2 arbitration 1 register low if2arb1l0 if2arb10 r/w 000749 h can0 - if2 arbitration 1 register high if2arb1h0 r/w 00074a h can0 - if2 arbitration 2 register low if2arb2l0 if2arb20 r/w 00074b h can0 - if2 arbitration 2 register high if2arb2h0 r/w 00074c h can0 - if2 message control register low if2mctrl0 if2mctr0 r/w 00074d h can0 - if2 message control register high if2mctrh0 r/w 00074e h can0 - if2 data a1 low if2dta1l0 if2dta10 r/w 00074f h can0 - if2 data a1 high if2dta1h0 r/w 000750 h can0 - if2 data a2 low if2dta2l0 if2dta20 r/w 000751 h can0 - if2 data a2 high if2dta2h0 r/w 000752 h can0 - if2 data b1 low if2dtb1l0 if2dtb10 r/w 000753 h can0 - if2 data b1 high if2dtb1h0 r/w 000754 h can0 - if2 data b2 low if2dtb2l0 if2dtb20 r/w 000755 h can0 - if2 data b2 high if2dtb2h0 r/w 000756 h - 00077f h reserved - 000780 h can0 - transmission request 1 register low treqr1l0 treqr10 r 000781 h can0 - transmission request 1 register high treqr1h0 r 000782 h can0 - transmission request 2 register low treqr2l0 treqr20 r 000783 h can0 - transmission request 2 register high treqr2h0 r 000784 h - 00078f h reserved - i/o map mb96(f)34x (26 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 50 fme-mb96340 rev 10 000790 h can0 - new data 1 register low newdt1l0 newdt10 r 000791 h can0 - new data 1 register high newdt1h0 r 000792 h can0 - new data 2 register low newdt2l0 newdt20 r 000793 h can0 - new data 2 register high newdt2h0 r 000794 h - 00079f h reserved - 0007a0 h can0 - interrupt pending 1 register low intpnd1l0 intpnd10 r 0007a1 h can0 - interrupt pending 1 register high intpnd1h0 r 0007a2 h can0 - interrupt pending 2 register low intpnd2l0 intpnd20 r 0007a3 h can0 - interrupt pending 2 register high intpnd2h0 r 0007a4 h - 0007af h reserved - 0007b0 h can0 - message valid 1 register low msgval1l0 msgval10 r 0007b1 h can0 - message valid 1 register high msgval1h0 r 0007b2 h can0 - message valid 2 register low msgval2l0 msgval20 r 0007b3 h can0 - message valid 2 register high msgval2h0 r 0007b4 h - 0007cd h reserved - 0007ce h can0 - output enable register coer0 r/w 0007cf h - 0007ff h reserved - 000800 h can1 - control register low ctrlrl1 ctrlr1 r/w 000801 h can1 - control register high (reserved) ctrlrh1 r 000802 h can1 - status register low statrl1 statr1 r/w 000803 h can1 - status register high (reserved) statrh1 r 000804 h can1 - error counter low (transmit) errcntl1 errcnt1 r 000805 h can1 - error counter high (receive) errcnth1 r 000806 h can1 - bit timing register low btrl1 btr1 r/w 000807 h can1 - bit timing register high btrh1 r/w 000808 h can1 - interrupt register low intrl1 intr1 r 000809 h can1 - interrupt register high intrh1 r i/o map mb96(f)34x (27 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 51 00080a h can1 - test register low testrl1 testr1 r/w 00080b h can1 - test register high (reserved) testrh1 r 00080c h can1 - brp extension register low brperl1 brper1 r/w 00080d h can1 - brp extension register high (reserved) brperh1 r 00080e h - 00080f h reserved - 000810 h can1 - if1 command request register low if1creql1 if1creq1 r/w 000811 h can1 - if1 command request register high if1creqh1 r/w 000812 h can1 - if1 command mask register low if1cmskl1 if1cmsk1 r/w 000813 h can1 - if1 command mask register high (re- served) if1cmskh1 r 000814 h can1 - if1 mask 1 register low if1msk1l1 if1msk11 r/w 000815 h can1 - if1 mask 1 register high if1msk1h1 r/w 000816 h can1 - if1 mask 2 register low if1msk2l1 if1msk21 r/w 000817 h can1 - if1 mask 2 register high if1msk2h1 r/w 000818 h can1 - if1 arbitration 1 register low if1arb1l1 if1arb11 r/w 000819 h can1 - if1 arbitration 1 register high if1arb1h1 r/w 00081a h can1 - if1 arbitration 2 register low if1arb2l1 if1arb21 r/w 00081b h can1 - if1 arbitration 2 register high if1arb2h1 r/w 00081c h can1 - if1 message control register low if1mctrl1 if1mctr1 r/w 00081d h can1 - if1 message control register high if1mctrh1 r/w 00081e h can1 - if1 data a1 low if1dta1l1 if1dta11 r/w 00081f h can1 - if1 data a1 high if1dta1h1 r/w 000820 h can1 - if1 data a2 low if1dta2l1 if1dta21 r/w 000821 h can1 - if1 data a2 high if1dta2h1 r/w 000822 h can1 - if1 data b1 low if1dtb1l1 if1dtb11 r/w 000823 h can1 - if1 data b1 high if1dtb1h1 r/w 000824 h can1 - if1 data b2 low if1dtb2l1 if1dtb21 r/w 000825 h can1 - if1 data b2 high if1dtb2h1 r/w 000826 h - 00083f h reserved - i/o map mb96(f)34x (28 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 52 fme-mb96340 rev 10 000840 h can1 - if2 command request register low if2creql1 if2creq1 r/w 000841 h can1 - if2 command request register high if2creqh1 r/w 000842 h can1 - if2 command mask register low if2cmskl1 if2cmsk1 r/w 000843 h can1 - if2 command mask register high (re- served) if2cmskh1 r 000844 h can1 - if2 mask 1 register low if2msk1l1 if2msk11 r/w 000845 h can1 - if2 mask 1 register high if2msk1h1 r/w 000846 h can1 - if2 mask 2 register low if2msk2l1 if2msk21 r/w 000847 h can1 - if2 mask 2 register high if2msk2h1 r/w 000848 h can1 - if2 arbitration 1 register low if2arb1l1 if2arb11 r/w 000849 h can1 - if2 arbitration 1 register high if2arb1h1 r/w 00084a h can1 - if2 arbitration 2 register low if2arb2l1 if2arb21 r/w 00084b h can1 - if2 arbitration 2 register high if2arb2h1 r/w 00084c h can1 - if2 message control register low if2mctrl1 if2mctr1 r/w 00084d h can1 - if2 message control register high if2mctrh1 r/w 00084e h can1 - if2 data a1 low if2dta1l1 if2dta11 r/w 00084f h can1 - if2 data a1 high if2dta1h1 r/w 000850 h can1 - if2 data a2 low if2dta2l1 if2dta21 r/w 000851 h can1 - if2 data a2 high if2dta2h1 r/w 000852 h can1 - if2 data b1 low if2dtb1l1 if2dtb11 r/w 000853 h can1 - if2 data b1 high if2dtb1h1 r/w 000854 h can1 - if2 data b2 low if2dtb2l1 if2dtb21 r/w 000855 h can1 - if2 data b2 high if2dtb2h1 r/w 000856 h - 00087f h reserved - 000880 h can1 - transmission request 1 register low treqr1l1 treqr11 r 000881 h can1 - transmission request 1 register high treqr1h1 r 000882 h can1 - transmission request 2 register low treqr2l1 treqr21 r 000883 h can1 - transmission request 2 register high treqr2h1 r 000884 h - 00088f h reserved - i/o map mb96(f)34x (29 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series fme-mb96340 rev 10 53 note: any write access to reserved addresses in the i/o map should not be performed. a read access to a reserved address results in reading ?? registers of resources which are described in this table, but which are not supported by the device, should also be handled as ?eserved? 000890 h can1 - new data 1 register low newdt1l1 newdt11 r 000891 h can1 - new data 1 register high newdt1h1 r 000892 h can1 - new data 2 register low newdt2l1 newdt21 r 000893 h can1 - new data 2 register high newdt2h1 r 000894 h - 00089f h reserved - 0008a0 h can1 - interrupt pending 1 register low intpnd1l1 intpnd11 r 0008a1 h can1 - interrupt pending 1 register high intpnd1h1 r 0008a2 h can1 - interrupt pending 2 register low intpnd2l1 intpnd21 r 0008a3 h can1 - interrupt pending 2 register high intpnd2h1 r 0008a4 h - 0008af h reserved - 0008b0 h can1 - message valid 1 register low msgval1l1 msgval11 r 0008b1 h can1 - message valid 1 register high msgval1h1 r 0008b2 h can1 - message valid 2 register low msgval2l1 msgval21 r 0008b3 h can1 - message valid 2 register high msgval2h1 r 0008b4 h - 0008cd h reserved - 0008ce h can1 - output enable register coer1 r/w 0008cf h - 0009ff h reserved - 000a00 h dma - io address block register 0 ioabk0 r/w 000a01 h dma - io address block register 1 ioabk1 r/w 000a02 h dma - io address block register 2 ioabk2 r/w 000a03 h dma - io address block register 3 ioabk3 r/w 000a04 h dma - io address block register 4 ioabk4 r/w 000a05 h dma - io address block register 5 ioabk5 r/w 000a06 h - 000bff h reserved - i/o map mb96(f)34x (30 of 30) address register abbreviation 8-bit access abbreviation 16-bit access access www.datasheet.in
mb96340 series 54 fme-mb96340 rev 10 interrupt vector table interrupt vector table mb96(f)34x (1 of 4) vector number offset in vector ta- ble vector name cleared by dma index in icr to program description 0 3fc h callv0 no - 1 3f8 h callv1 no - 2 3f4 h callv2 no - 3 3f0 h callv3 no - 4 3ec h callv4 no - 5 3e8 h callv5 no - 6 3e4 h callv6 no - 7 3e0 h callv7 no - 8 3dc h reset no - 9 3d8 h int9 no - 10 3d4 h exception no - 11 3d0 h nmi no - non-maskable interrupt 12 3cc h dly no 12 delayed interrupt 13 3c8 h rc_timer no 13 rc timer 14 3c4 h mc_timer no 14 main clock timer 15 3c0 h sc_timer no 15 sub clock timer 16 3bc h reserved no 16 reserved 17 3b8 h extint0 yes 17 external interrupt 0 18 3b4 h extint1 yes 18 external interrupt 1 19 3b0 h extint2 yes 19 external interrupt 2 20 3ac h extint3 yes 20 external interrupt 3 21 3a8 h extint4 yes 21 external interrupt 4 22 3a4 h extint5 yes 22 external interrupt 5 23 3a0 h extint6 yes 23 external interrupt 6 24 39c h extint7 yes 24 external interrupt 7 25 398 h extint8 yes 25 external interrupt 8 26 394 h extint9 yes 26 external interrupt 9 27 390 h extint10 yes 27 external interrupt 10 www.datasheet.in
mb96340 series fme-mb96340 rev 10 55 28 38c h extint11 yes 28 external interrupt 11 29 388 h extint12 yes 29 external interrupt 12 30 384 h extint13 yes 30 external interrupt 13 31 380 h extint14 yes 31 external interrupt 14 32 37c h extint15 yes 32 external interrupt 15 33 378 h can0 no 33 can controller 0 (except mb96(f)34xayy or mb96(f)34xcyy) 34 374 h can1 no 34 can controller 1 (except mb96(f)34xayy, mb96(f)34xcyy, mb96f345dyy or mb96f345fyy) 35 370 h ppg0 yes 35 programmable pulse generator 0 36 36c h ppg1 yes 36 programmable pulse generator 1 37 368 h ppg2 yes 37 programmable pulse generator 2 38 364 h ppg3 yes 38 programmable pulse generator 3 39 360 h ppg4 yes 39 programmable pulse generator 4 40 35c h ppg5 yes 40 programmable pulse generator 5 41 358 h ppg6 yes 41 programmable pulse generator 6 42 354 h ppg7 yes 42 programmable pulse generator 7 43 350 h ppg8 yes 43 programmable pulse generator 8 44 34c h ppg9 yes 44 programmable pulse generator 9 45 348 h ppg10 yes 45 programmable pulse generator 10 46 344 h ppg11 yes 46 programmable pulse generator 11 47 340 h ppg12 yes 47 programmable pulse generator 12 48 33c h ppg13 yes 48 programmable pulse generator 13 49 338 h ppg14 yes 49 programmable pulse generator 14 50 334 h ppg15 yes 50 programmable pulse generator 15 51 330 h rlt0 yes 51 reload timer 0 52 32c h rlt1 yes 52 reload timer 1 53 328 h rlt2 yes 53 reload timer 2 54 324 h rlt3 yes 54 reload timer 3 interrupt vector table mb96(f)34x (2 of 4) vector number offset in vector ta- ble vector name cleared by dma index in icr to program description www.datasheet.in
mb96340 series 56 fme-mb96340 rev 10 55 320 h ppgrlt yes 55 reload timer 6 - dedicated for ppg 56 31c h icu0 yes 56 input capture unit 0 57 318 h icu1 yes 57 input capture unit 1 58 314 h icu2 yes 58 input capture unit 2 59 310 h icu3 yes 59 input capture unit 3 60 30c h icu4 yes 60 input capture unit 4 61 308 h icu5 yes 61 input capture unit 5 62 304 h icu6 yes 62 input capture unit 6 63 300 h icu7 yes 63 input capture unit 7 64 2fc h ocu0 yes 64 output compare unit 0 65 2f8 h ocu1 yes 65 output compare unit 1 66 2f4 h ocu2 yes 66 output compare unit 2 67 2f0 h ocu3 yes 67 output compare unit 3 68 2ec h ocu4 yes 68 output compare unit 4 69 2e8 h ocu5 yes 69 output compare unit 5 70 2e4 h ocu6 yes 70 output compare unit 6 71 2e0 h ocu7 yes 71 output compare unit 7 72 2dc h frt0 yes 72 free running timer 0 73 2d8 h frt1 yes 73 free running timer 1 74 2d4 h iic0 yes 74 i2c interface 75 2d0 h iic1 yes 75 i2c interface 76 2cc h adc0 yes 76 a/d converter 77 2c8 h alarm0 no 77 alarm comparator 0 (except mb96f345dyy or mb96f345fyy) 78 2c4 h alarm1 no 78 alarm comparator 1 (except mb96f345dyy or mb96f345fyy) 79 2c0 h linr0 yes 79 lin usart 0 rx 80 2bc h lint0 yes 80 lin usart 0 tx 81 2b8 h linr1 yes 81 lin usart 1 rx 82 2b4 h lint1 yes 82 lin usart 1 tx interrupt vector table mb96(f)34x (3 of 4) vector number offset in vector ta- ble vector name cleared by dma index in icr to program description www.datasheet.in
mb96340 series fme-mb96340 rev 10 57 83 2b0 h linr2 yes 83 lin usart 2 rx 84 2ac h lint2 yes 84 lin usart 2 tx 85 2a8 h linr3 yes 85 lin usart 3 rx 86 2a4 h lint3 yes 86 lin usart 3 tx 87 2a0 h flash_a no 87 flash memory a (only flash devices) 88 29c h flash_b no 88 flash memory b (only mb96f348t/h/c) 89 298 h linr7 yes 89 lin usart 7 rx 90 294 h lint7 yes 90 lin usart 7 tx 91 290 h linr8 yes 91 lin usart 8 rx 92 28c h lint8 yes 92 lin usart 8 tx 93 288 h linr9 yes 93 lin usart 9 rx 94 284 h lint9 yes 94 lin usart 9 tx 95 280 h rtc0 no 95 real timer clock 96 27c h cal0 no 96 clock calibration unit 97 278 h dflash_a yes 97 data flash a (only mb96f345dyy, mb96f345fyy) interrupt vector table mb96(f)34x (4 of 4) vector number offset in vector ta- ble vector name cleared by dma index in icr to program description www.datasheet.in
mb96340 series 58 fme-mb96340 rev 10 handling devices special care is required for the following when handling the device: latch-up prevention unused pins handling external clock usage unused sub clock signal notes on pll clock mode operation power supply pins (v cc /v ss ) crystal oscillator circuit turn on sequence of power supply to a/d converter and analog inputs pin handling when not using the a/d converter notes on energization stabilization of power supply voltage serial communication handling of data flash 1. latch-up prevention cmos ic chips may suffer latch-up under the following conditions: a voltage higher than v cc or lower than v ss is applied to an input or output pin. a voltage higher than the rated voltage is applied between v cc pins and v ss pins. the av cc power supply is applied before the v cc voltage. latch-up may increase the power supply current dramatically, causing thermal damages to the device. for the same reason, extra care is required to not let the analog power-supply voltage (av cc , avrh) exceed the digital power-supply voltage. 2. unused pins handling unused input pins can be left open when the input is disabled (corresponding bit of port input enable register pier = 0). leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent damage of the device. they must therefore be pulled up or pulled down through resistors. to prevent latch-up, those resistors should be more than 2 k ? . unused bidirectional pins can be set either to the output state and be then left open, or to the input state with either input disabled or external pull-up/pull-down resistor as described above. 3. external clock usage the permitted frequency range of an external clock depends on the oscillator type and con?uration. see ac characteristics for detailed modes and frequency limits. single and opposite phase external clocks must be connected as follows: 1. single phase external clock when using a single phase external clock, x0 (x0a) pin must be driven and x1 (x1a) pin left open. x0 x1 www.datasheet.in
mb96340 series fme-mb96340 rev 10 59 2. opposite phase external clock when using an opposite phase external clock, x1 (x1a) must be supplied with a clock signal which has the opposite phase to the x0 (x0a) pins. 4. unused sub clock signal if the pins x0a and x1a are not connected to an oscillator, a pull-down resistor must be connected on the x0a pin and the x1a pin must be left open. 5. notes on pll clock mode operation if the pll clock mode is selected and no external oscillator is operating or no external clock is supplied, the microcontroller attempts to work with the free oscillating pll. performance of this operation, however, cannot be guaranteed. 6. power supply pins (v cc / v ss ) it is required that all v cc -level as well as all v ss -level power supply pins are at the same potential. if there is more than one v cc or v ss level, the device may operate incorrectly or be damaged even within the guaranteed operating range. v cc and v ss must be connected to the device from the power supply with lowest possible impedance. as a measure against power supply noise, it is required to connect a bypass capacitor of about 0.1 f between v cc and v ss as close as possible to v cc and v ss pins. 7. crystal oscillator and ceramic resonator circuit noise at x0, x1 pins or x0a, x1a pins might cause abnormal operation. it is required to provide bypass capacitors with shortest possible distance to x0, x1 pins and x0a, x1a pins, crystal oscillator (or ceramic resonator) and ground lines, and, to the utmost effort, that the lines of oscillation circuit do not cross the lines of other circuits. it is highly recommended to provide a printed circuit board art work surrounding x0, x1 pins and x0a, x1a pins with a ground area for stabilizing the operation. it is highly recommended to evaluate the quartz/mcu or resonator/mcu system at the quartz or resonator manufacturer, especially when using low-q resonators at higher frequencies. 8. turn on sequence of power supply to a/d converter and analog inputs it is required to turn the a/d converter power supply (av cc , avrh, avrl) and analog inputs (ann) on after turning the digital power supply (v cc ) on. it is also required to turn the digital power off after turning the a/d converter supply and analog inputs off. in this case, the voltage must not exceed avrh or av cc (turning the analog and digital power supplies simultaneously on or off is acceptable). 9. pin handling when not using the a/d converter it is required to connect the unused pins of the a/d converter as av cc = v cc , av ss = avrh = avrl = v ss . 10. notes on power-on to prevent malfunction of the internal voltage regulator, supply voltage pro?e while turning the power supply on should be slower than 50 s from 0.2 v to 2.7 v. x0 x1 www.datasheet.in
mb96340 series 60 fme-mb96340 rev 10 11. stabilization of power supply voltage if the power supply voltage varies acutely even within the operation safety range of the vcc power supply voltage, a malfunction may occur. the vcc power supply voltage must therefore be stabilized. as stabilization guidelines, the power supply voltage must be stabilized in such a way that vcc ripple ?ctuations (peak to peak value) in the commercial frequencies (50 to 60 hz) fall within 10% of the standard vcc power supply voltage and the transient ?ctuation rate becomes 0.1v/ s or less in instantaneous ?ctuation for power supply switching. 12. serial communication there is a possibility to receive wrong data due to noise or other causes on the serial communication. therefore, design a printed circuit board so as to avoid noise. consider receiving of wrong data when designing the system. for example apply a checksum and retransmit the data if an error occurs. 13. handling of data flash the data flash requires different and additional control signals for parallel programming. please check with your programming equipment maker for support of this interface. www.datasheet.in
mb96340 series fme-mb96340 rev 10 61 electrical characteristics 1. absolute maximum ratings parameter symbol rating unit remarks min max power supply voltage v cc v ss - 0.3 v ss + 6.0 v av cc v ss - 0.3 v ss + 6.0 v v cc = av cc *1 ad converter voltage references avrh, avrl v ss - 0.3 v ss + 6.0 v av cc avrh, av cc avrl, avrh > avrl, avrl av ss input voltage v i v ss - 0.3 v ss + 6.0 v v i v cc + 0.3v *2 output voltage v o v ss - 0.3 v ss + 6.0 v v o v cc + 0.3v *2 maximum clamp current i clamp -4.0 +4.0 ma applicable to general purpose i/o pins *3 total maximum clamp current |i clamp | - 40 ma applicable to general purpose i/o pins *3 ??level maximum output current i ol1 - 15 ma normal outputs with driving strength set to 5ma ??level average output current i olav1 - 5 ma normal outputs with driving strength set to 5ma ??level maximum overall output current i ol1 - 100 ma normal outputs ??level average overall output current i olav1 - 50 ma normal outputs ??level maximum output current i oh1 - -15 ma normal outputs with driving strength set to 5ma ??level average output current i ohav1 - -5 ma normal outputs with driving strength set to 5ma ? level maximum overall output current i oh1 - -100 ma normal outputs ??level average overall output current i ohav1 - -50 ma normal outputs permitted power dissipation (flash de- vices in qfp package) *4 p d - 430 *5 mw t a =105 o c - 750 *5 mw t a =90 o c - 540 *5 mw t a =125 o c, no flash program/ erase *6 permitted power dissipation (mb96f346/f347/f348 in lqfp pack- age) *4 p d - 375 *5 mw t a =105 o c - 750 *5 mw t a =85 o c - 470 *5 mw t a =125 o c, no flash program/ erase *6 - 560 *5 mw t a =120 o c, no flash program/ erase *6 www.datasheet.in
mb96340 series 62 fme-mb96340 rev 10 *1: av cc and v cc must be set to the same voltage. it is required that av cc does not exceed v cc and that the voltage at the analog inputs does not exceed av cc neither when the power is switched on. *2: v i and v o should not exceed v cc + 0.3 v. v i should also not exceed the speci?d ratings. however if the maximum current to/from a input is limited by some means with external components, the i clamp rating super- sedes the v i rating. input/output voltages of standard ports depend on v cc. *3: ? applicable to all general purpose i/o pins (pnn_m) ? use within recommended operating conditions. ? use at dc voltage (current) ? the +b signal should always be applied a limiting resistance placed between the +b signal and the microcontroller. ? the value of the limiting resistance should be set so that when the +b signal is applied the input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods. ? note that when the microcontroller drive current is low, such as in the power saving modes, the +b input potential may pass through the protective diode and increase the potential at the vcc pin, and this may affect other devices. ? note that if a +b signal is input when the microcontroller power supply is off (not ?ed at 0 v), the power supply is provided from the pins, so that incomplete operation may result. ? note that if the +b input is applied during power-on, the power supply is provided from the pins and the resulting supply voltage may not be suf?ient to operate the power reset (except devices with persistent low voltage reset in internal vector mode). permitted power dissipation (mb96f345 in lqfp package) *4 p d - 335 *5 mw t a =105 o c - 670 *5 mw t a =85 o c - 840 *5 mw t a =75 o c - 420 *5 mw t a =125 o c, no flash program/ erase *6 - 590 *5 mw t a =115 o c, no flash program/ erase *6 permitted power dissipation (mask rom devices) *4 p d - 350 mw t a =105 o c - 360 mw t a =125 o c *6 operating ambient temperature t a 0 +70 o c mb96v300b -40 +105 -40 +125 *6 storage temperature t stg -55 +150 o c parameter symbol rating unit remarks min max www.datasheet.in
mb96340 series fme-mb96340 rev 10 63 ? sample recommended circuits: *4: the maximum permitted power dissipation depends on the ambient temperature, the air ?w velocity and the thermal conductance of the package on the pcb. the actual power dissipation depends on the customer application and can be calculated as follows: p d = p io + p int p io = (v ol * i ol + v oh * i oh ) (io load power dissipation, sum is performed on all io ports) p int = v cc * (i cc + i a ) (internal power dissipation) i cc is the total core current consumption into v cc as described in the ?c characteristics and depends on the selected operation mode and clock frequency and the usage of functions like flash programming or the clock modulator. i a is the analog current consumption into av cc . *5: worst case value for a package mounted on single layer pcb at speci?d t a without air ?w. *6: please contact fujitsu for reliability limitations when using under these conditions. warning: semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. do not exceed these ratings. p-ch n-ch v cc r protective diode limiting resistance +b input (0v to 16v) www.datasheet.in
mb96340 series 64 fme-mb96340 rev 10 2. recommended operating conditions warning: the recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. all of the devices electrical characteristics are warranted when the device is operated within these ranges. always use semiconductor devices within their recommended operating condition ranges. operation outside these ranges may adversely affect reliability and could result in device failure. no warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. users considering application outside the listed conditions are advised to contact their fujitsu representatives beforehand. parameter symbol value unit remarks min typ max power supply voltage v cc 3.0 - 5.5 v smoothing capacitor at c pin c s 3.5 4.7 15 f use a x7r ceramic capacitor or a capacitor that has similar fre- quency characteristics www.datasheet.in
mb96340 series fme-mb96340 rev 10 65 3. dc characteristics (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol pin condition value unit remarks min typ max input h voltage v ih port inputs pnn_m cmos hysteresis 0.8/0.2 input se- lected 0.8 v cc - v cc + 0.3 v not available in mb96f345 cmos hysteresis 0.7/0.3 input se- lected 0.7 v cc - v cc + 0.3 vv cc 4.5v 0.74 v cc - v cc + 0.3 vv cc < 4.5v automotive hysteresis input selected 0.8 v cc - v cc + 0.3 v ttl input select- ed 2.0 - v cc + 0.3 v not available in mb96f345 v ihx0f x0 external clock in ?ast clock input mode 0.8 v cc - v cc + 0.3 v not available in mb96f34xy/r/axa v ihx0s x0,x1, x0a,x1a external clock in ?scillation mode 2.5 - v cc + 0.3 v v ihr rstx - 0.8 v cc - v cc + 0.3 v cmos hysteresis in- put v ihm md2-md0 - v cc - 0.3 - v cc + 0.3 v input l voltage v il port inputs pnn_m cmos hysteresis 0.8/0.2 input se- lected v ss - 0.3 - 0.2 v cc v not available in mb96f345 cmos hysteresis 0.7/0.3 input se- lected v ss - 0.3 - 0.3 v cc v automotive hysteresis input selected v ss - 0.3 - 0.5 v cc vv cc 4.5v v ss - 0.3 - 0.46 v cc v cc < 4.5v ttl input select- ed v ss - 0.3 - 0.8 v not available in mb96f345 v ilx0f x0 external clock in ?ast clock input mode v ss - 0.3 - 0.2 v cc v not available in mb96f34xy/r/axa v ilx0s x0,x1, x0a,x1a external clock in ?scillation mode v ss - 0.3 - 0.4 v v ilr rstx - v ss - 0.3 - 0.2 v cc v cmos hysteresis in- put v ilm md2-md0 - v ss - 0.3 - v ss + 0.3 v www.datasheet.in
mb96340 series 66 fme-mb96340 rev 10 output h voltage v oh2 normal outputs 4.5v v cc 5.5v i oh = -2ma v cc - 0.5 -- v driving strength set to 2ma (podr:od=1) 3.0v v cc < 4.5v i oh = -1.6ma v oh5 normal outputs 4.5v v cc 5.5v i oh = -5ma v cc - 0.5 -- v driving strength set to 5ma (podr:od=0) 3.0v v cc < 4.5v i oh = -3ma v oh3 3ma out- puts 4.5v v cc 5.5v i oh = -3ma v cc - 0.5 -- v i/o circuit type ? 3.0v v cc < 4.5v i oh = -2ma output l voltage v ol2 normal outputs 4.5v v cc 5.5v i ol = +2ma - - 0.4 v driving strength set to 2ma (podr:od=1) 3.0v v cc < 4.5v i ol = +1.6ma v ol5 normal outputs 4.5v v cc 5.5v i ol = +5ma - - 0.4 v driving strength set to 5ma (podr:od=0) 3.0v v cc < 4.5v i ol = +3ma v ol3 3ma out- puts 3.0v v cc 5.5v i ol = +3ma - - 0.4 v i/o circuit type ? input leak current i il pnn_m v ss < v i < v cc av ss ,avrl mb96340 series fme-mb96340 rev 10 67 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit power supply current in run modes* i ccpll pll run mode with clks1/2 = clkb = clkp1 = 16mhz, clkp2 = 8mhz 1 flash/rom wait state (clkrc and clksc stopped) +25?c 8 11 ma MB96345/346 +125?c 8.5 13 +25?c 15 20 ma mb96f345 +125?c 16 23 +25?c 17 22 ma mb96f346/f347/f348y/ r/ayy +125?c 18.5 25.5 +25?c 16 21 ma mb96f348t/h/cyb/c +125?c 17.5 24.5 pll run mode with clks1/2 = clkb = clkp1 = 32mhz, clkp2 = 16mhz 2 flash/rom wait states (clkrc and clksc stopped) +25?c 14 18 ma MB96345/346 +125?c 14.5 20 +25?c 23.5 29.5 ma mb96f345 +125?c 25 32.5 +25?c 26 32 ma mb96f346/f347/f348y/ r/ayy +125?c 28 36 +25?c 25 31 ma mb96f348t/h/cyb/c +125?c 27 35 pll run mode with clks1/2 = 48mhz, clkb = clkp1/2 = 24mhz 0 flash/rom wait states (clkrc and clksc stopped) +25?c 13 17 ma MB96345/346 +125?c 13.5 19 +25?c 27 39 ma mb96f345 +125?c 29 42 +25?c 31 43 ma mb96f346/f347/f348y/ r/ayy +125?c 33 47 +25?c 30 42 ma mb96f348t/h/cyb/c +125?c 32 46 www.datasheet.in
mb96340 series 68 fme-mb96340 rev 10 power supply current in run modes* i ccpll pll run mode with clks1/2 = clkb = clkp1= 56mhz, clkp2 = 28mhz 2 flash/rom wait states (clkrc and clksc stopped. core voltage at 1.9v) +25?c 24 29 ma MB96345/346 +125?c 24.5 31 +25?c 46 57 ma mb96f346/f347/f348y/ r/ayy +125?c 48 61 +25?c 44 55 ma mb96f348t/h/cyb/c +125?c 46 59 pll run mode with clks1/2 = 72mhz, clkb = clkp1 = 36mhz, clkp2 = 18mhz 1 flash wait state (clkrc and clksc stopped. core voltage at 1.9v) +25?c 38 51 ma mb96f346/f347/f348y/ r/ayy +125?c 40 55 pll run mode with clks1/2 = 80mhz, clkb = clkp1 = 40mhz, clkp2 = 20mhz 1 flash wait state (clkrc and clksc stopped. core voltage at 1.9v) +25?c 38 51 ma mb96f345 +125?c 40 54 pll run mode with clks1/2 = 96mhz, clkb = clkp1= 48mhz, clkp2 = 24mhz 1 flash/rom wait state (clkrc and clksc stopped. core voltage at 1.9v) +25?c 24 28.5 ma MB96345/346 +125?c 24.5 30.5 +25?c 49 62 ma mb96f348t/h/cyb/c +125?c 51 66 i ccmain main run mode with clks1/2 = clkb = clkp1/2 = 4mhz 1 flash/rom wait state (clkpll, clksc and clkrc stopped) +25?c 2.3 3.3 ma MB96345/346 +125?c 2.8 5.3 +25?c 4 5 ma mb96f345 +125?c 4.6 7.2 +25?c 4.5 5.5 ma mb96f346/f347/f348 +125?c 5.2 8.5 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series fme-mb96340 rev 10 69 power supply current in run modes* i ccrch rc run mode with clks1/2 = clkb = clkp1/2 = 2mhz 1 flash/rom wait state (clkmc, clkpll and clksc stopped) +25?c 1.5 2.5 ma MB96345/346 +125?c 2 4.4 +25?c 2.5 3.5 ma mb96f345 +125?c 3.1 5.7 +25?c 2.9 4 ma mb96f346/f347/f348 +125?c 3.6 7 i ccrcl rc run mode with clks1/2 = clkb = clkp1/2 = 100khz, smcr:lpms = 0 1 flash/rom wait state (clkmc, clkpll and clksc stopped. voltage regulator in high power mode) +25?c 0.35 0.55 ma MB96345/346 +125?c 0.75 2.3 +25?c 0.18 0.3 ma mb96f345 +125?c 0.73 2.3 +25?c 0.4 0.6 ma mb96f346/f347/f348 +125?c 0.95 3.4 rc run mode with clks1/2 = clkb = clkp1/2 = 100khz, smcr:lpms = 1 1 flash/rom wait state (clkmc, clkpll and clksc stopped. voltage regulator in low power mode, no flash program- ming/erasing allowed) +25?c 0.08 0.17 ma MB96345/346 +125?c 0.47 1.92 +25?c 0.15 0.25 ma mb96f345 +125?c 0.7 2.25 +25?c 0.15 0.25 ma mb96f346/f347/f348 +125?c 0.7 3.05 i ccsub sub run mode with clks1/2 = clkb = clkp1/2 = 32khz 1 flash/rom wait state (clkmc, clkpll and clkrc stopped, no flash programming/erasing al- lowed) +25?c 0.04 0.12 ma MB96345/346 +125?c 0.43 1.85 +25?c 0.1 0.2 ma mb96f345 +125?c 0.65 2.2 +25?c 0.1 0.2 ma mb96f346/f347/f348 +125?c 0.65 3 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series 70 fme-mb96340 rev 10 power supply current in sleep modes* i ccspll pll sleep mode with clks1/2 = clkp1 = 16mhz, clkp2 = 8mhz (clkrc and clksc stopped) +25?c 4 6 ma MB96345/346 +125?c 4.5 8 +25?c 4 6 ma mb96f345 +125?c 4.7 8.5 +25?c 4 6 ma mb96f346/f347/f348y/ r/ayy +125?c 4.7 9 +25?c 4.7 6.7 ma mb96f348t/h/cyb/c +125?c 5.5 9.7 pll sleep mode with clks1/2 = clkp1 = 32mhz, clkp2 = 16mhz (clkrc and clksc stopped) +25?c 7.5 10 ma MB96345/346 +125?c 8 12 +25?c 7 9.5 ma mb96f345 +125?c 7.7 12 +25?c 7.5 10 ma mb96f346/f347/f348y/ r/ayy +125?c 8.4 13 +25?c 8.5 11 ma mb96f348t/h/cyb/c +125?c 9.5 14 pll sleep mode with clks1/2 = 48mhz, clkp1/2 = 24mhz (clkrc and clksc stopped) +25?c 7.5 9.5 ma MB96345/346 +125?c 8 11.5 +25?c 7 9 ma mb96f345 +125?c 7.7 11.5 +25?c 7.5 9.5 ma mb96f346/f347/f348y/ r/ayy +125?c 8.4 12.5 +25?c 8.5 10.5 ma mb96f348t/h/cyb/c +125?c 9.5 13.5 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series fme-mb96340 rev 10 71 power supply current in sleep modes* i ccspll pll sleep mode with clks1/2 = clkp1= 56mhz, clkp2 = 28mhz (clkrc and clksc stopped. core voltage at 1.9v) +25?c 12.5 16 ma MB96345/346 +125?c 13 18 +25?c 12.5 16 ma mb96f346/f347/f348y/ r/ayy +125?c 13.5 19 +25?c 13.5 17 ma mb96f348t/h/cyb/c +125?c 14.5 20 pll sleep mode with clks1/2 = 72mhz, clkp1 = 36mhz, clkp2 = 18mhz (clkrc and clksc stopped. core voltage at 1.9v) +25?c 9.5 12.5 ma mb96f346/f347/f348y/ r/ayy +125?c 10.5 15.5 pll sleep mode with clks1/2 = 80mhz, clkp1 = 40mhz, clkp2 = 20mhz (clkrc and clksc stopped. core voltage at 1.9v) +25?c 11 13.5 ma mb96f345 +125?c 11.7 16 pll sleep mode with clks1/2 = 96mhz, clkp1= 48mhz, clkp2 = 24mhz (clkrc and clksc stopped. core voltage at 1.9v) +25?c 13 16 ma MB96345/346 +125?c 13.5 18 +25?c 15 18 ma mb96f348t/h/cyb/c +125?c 16 21 i ccsmain main sleep mode with clks1/2 = clkp1/2 = 4mhz (clkpll, clksc and clkrc stopped) +25?c 1.3 1.8 ma MB96345/346 +125?c 1.8 3.7 +25?c 1 1.3 ma mb96f345 +125?c 1.6 3.4 +25?c 1.3 1.8 ma mb96f346/f347/f348 +125?c 1.9 4.6 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series 72 fme-mb96340 rev 10 power supply current in sleep modes* i ccsrch rc sleep mode with clks1/2 = clkp1/2 = 2mhz (clkmc, clkpll and clksc stopped) +25?c 0.8 1.4 ma MB96345/346 +125?c 1.3 3.2 +25?c 0.55 1.1 ma mb96f345 +125?c 1.1 3.1 +25?c 0.8 1.4 ma mb96f346/f347/f348 +125?c 1.4 4.2 i ccsrcl rc sleep mode with clks1/2 = clkp1/2 = 100khz, smcr:lpmss = 0 (clkmc, clkpll and clksc stopped. voltage regulator in high power mode) +25?c 0.3 0.5 ma MB96345/346 +125?c 0.7 2.3 +25?c 0.09 0.2 ma mb96f345 +125?c 0.59 2.2 +25?c 0.3 0.5 ma mb96f346/f347/f348 +125?c 0.8 3.3 rc sleep mode with clks1/2 = clkp1/2 = 100khz, smcr:lpmss = 1 (clkmc, clkpll and clksc stopped. voltage regulator in low power mode) +25?c 0.05 0.14 ma MB96345/346 +125?c 0.44 1.9 +25?c 0.05 0.15 ma mb96f345 +125?c 0.56 2.1 +25?c 0.05 0.15 ma mb96f346/f347/f348 +125?c 0.56 2.9 i ccssub sub sleep mode with clks1/2 = clkp1/2 = 32khz (clkmc, clkpll and clkrc stopped) +25?c 0.04 0.12 ma MB96345/346 +125?c 0.43 1.85 +25?c 0.04 0.12 ma mb96f345 +125?c 0.54 2.1 +25?c 0.04 0.12 ma mb96f346/f347/f348 +125?c 0.54 2.9 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series fme-mb96340 rev 10 73 power supply current in timer modes* i cctpll pll timer mode with clkmc = 4mhz, clkpll = 48mhz (clkrc and clksc stopped) +25?c 1.4 1.9 ma MB96345/346 +125?c 1.9 3.9 +25?c 1.3 1.8 ma mb96f345 +125?c 1.9 4 +25?c 1.5 2 ma mb96f346/f347/f348 +125?c 2.1 5 i cctmain main timer mode with clkmc = 4mhz, smcr:lpmss = 0 (clkpll, clkrc and clksc stopped. voltage regulator in high power mode) +25?c 0.35 0.5 ma MB96345/346 +125?c 0.7 2.3 +25?c 0.11 0.2 ma mb96f345 +125?c 0.63 2.2 +25?c 0.35 0.5 ma mb96f346/f347/f348 +125?c 0.85 3.3 main timer mode with clkmc = 4mhz, smcr:lpmss = 1 (clkpll, clkrc and clksc stopped. voltage regulator in low power mode) +25?c 0.08 0.15 ma MB96345/346 +125?c 0.47 1.9 +25?c 0.08 0.15 ma mb96f345 +125?c 0.6 2.1 +25?c 0.08 0.15 ma mb96f346/f347/f348 +125?c 0.6 2.9 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series 74 fme-mb96340 rev 10 power supply current in timer modes* i cctrch rc timer mode with clkrc = 2mhz, smcr:lpmss = 0 (clkmc, clkpll and clksc stopped. voltage regulator in high power mode) +25?c 0.35 0.5 ma MB96345/346 +125?c 0.7 2.3 +25?c 0.13 0.2 ma mb96f345 +125?c 0.63 2.2 +25?c 0.35 0.5 ma mb96f346/f347/f348 +125?c 0.85 3.3 rc timer mode with clkrc = 2mhz, smcr:lpmss = 1 (clkmc, clkpll and clksc stopped. voltage regulator in low power mode) +25?c 0.07 0.15 ma MB96345/346 +125?c 0.46 1.9 +25?c 0.07 0.15 ma mb96f345 +125?c 0.6 2.1 +25?c 0.07 0.15 ma mb96f346/f347/f348 +125?c 0.6 2.9 i cctrcl rc timer mode with clkrc = 100khz, smcr:lpmss = 0 (clkmc, clkpll and clksc stopped. voltage regulator in high power mode) +25?c 0.3 0.45 ma MB96345/346 +125?c 0.65 2.2 +25?c 0.08 0.15 ma mb96f345 +125?c 0.58 2.1 +25?c 0.3 0.45 ma mb96f346/f347/f348 +125?c 0.8 3.2 rc timer mode with clkrc = 100khz, smcr:lpmss = 1 (clkmc, clkpll and clksc stopped. voltage regulator in low power mode) +25?c 0.03 0.1 ma MB96345/346 +125?c 0.41 1.85 +25?c 0.03 0.1 ma mb96f345 +125?c 0.53 2.05 +25?c 0.03 0.1 ma mb96f346/f347/f348 +125?c 0.53 2.85 (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series fme-mb96340 rev 10 75 power supply current in timer modes* i cctsub sub timer mode with clksc = 32khz (clkmc, clkpll and clkrc stopped) +25?c 0.035 0.1 ma MB96345/346 +125?c 0.42 1.85 +25?c 0.035 0.1 ma mb96f345 +125?c 0.53 2.05 +25?c 0.035 0.1 ma mb96f346/f347/f348 +125?c 0.53 2.85 power supply current in stop mode i cch vrcr:lpmb[2:0] = 110 b (core voltage at 1.8v) +25?c 0.02 0.08 ma MB96345/346 +125?c 0.4 1.8 +25?c 0.02 0.08 ma mb96f345 +125?c 0.52 2.0 +25?c 0.02 0.08 ma mb96f346/f347/f348 +125?c 0.52 2.8 vrcr:lpmb[2:0] = 000 b (core voltage at 1.2v) +25?c 0.015 0.06 ma MB96345/346 +125?c 0.3 1.4 +25?c 0.015 0.06 ma mb96f345 +125?c 0.4 1.5 +25?c 0.015 0.06 ma mb96f346/f347/f348 +125?c 0.4 2.3 power supply current for active low voltage de- tector i cclvd low voltage detector en- abled (rcr:lvde = 1) +25?c 5 10 a mb96f345 must be added to all cur- rent above +125?c 7 20 a +25?c 90 140 a other devices must be added to all cur- rent above +125?c 100 150 power supply current for active clock modulator i ccclomo clock modulator enabled (cmcr:pdx = 1) - 3 4.5 ma must be added to all cur- rent above flash write/ erase current i ccflash current for one flash module -1540ma must be added to all cur- rent above i ccdflash current for one data flash module 10 20 ma must be added to all cur- rent above (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series 76 fme-mb96340 rev 10 input capaci- tance c in --515pf other than c, av cc ,av ss , avrh, avrl, v cc , v ss * the power supply current is measured with a 4mhz external clock connected to the main oscillator and a 32khz external clock connected to the sub oscillator. see chapter ?tandby mode and voltage regulator control circuit of the hardware manual for further details about voltage regulator control. (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol condition (at t a ) value remarks typ max unit www.datasheet.in
mb96340 series fme-mb96340 rev 10 77 4. ac characteristics source clock timing (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol pin value unit remarks min typ max clock frequency f c x0, x1 3 - 16 mhz when using a crystal oscillator, pll off 0 - 16 mhz when using an opposite phase external clock, pll off 3.5 - 16 mhz when using a crystal oscillator or oppo- site phase external clock, pll on clock frequency f fci x0 0 - 56 mhz when using a single phase external clock in ?ast clock input mode?(not available in mb96f34xy/r/axa), pll off 3.5 - 56 mhz when using a single phase external clock in ?ast clock input mode?(not available in mb96f34xy/r/axa), pll on clock frequency f cl x0a, x1a 32 32.768 100 khz when using an oscillation circuit 0 - 100 khz when using an opposite phase external clock x0a 0 - 50 khz when using a single phase external clock clock frequency f cr - 50 100 200 khz when using slow frequency of rc oscil- lator 1 2 4 mhz when using fast frequency of rc oscil- lator rc clock stabili- zation time t rcstab - 64 or 256 rc clock cycles applied after any reset and when acti- vating the rc oscillator. mb96f345: 256 cycles others 64 cycles pll clock fre- quency f clkvco - 64 - 200 mhz permitted vco output frequency of pll (clkvco) pll phase jitter t pskew --- 5ns for clkmc (pll input clock) 4 mhz, jitter coming from external oscillator, crystal or resonator is not covered input clock pulse width p wh , p wl x0,x1 8 - - ns duty ratio is about 30% to 70% input clock pulse width p whl , p wll x0a,x1a 5 - - s www.datasheet.in
mb96340 series 78 fme-mb96340 rev 10 x0 t cyl p wh p wl v il v ih x0a t cyll p whl p wll v il v ih www.datasheet.in
mb96340 series fme-mb96340 rev 10 79 internal clock timing (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol core voltage settings unit remarks 1.8v 1.9v min max min max internal system clock fre- quency (clks1 and clks2) f clks1 , f clks2 0 92 0 96 mhz others than below 0 86 0 96 mhz mb96f348t/h/cxb/c 0 72 0 80 mhz mb96f345 0 68 0 74 mhz mb96f34xy/r/axx internal cpu clock fre- quency (clkb), internal peripheral clock frequency (clkp1) f clkb , f clkp1 0 52 0 56 mhz others than below 0 36 0 40 mhz mb96f345 internal peripheral clock frequency (clkp2) f clkp2 0 28 0 32 mhz others than below 0 26 0 28 mhz mb96f34xy/r/axx www.datasheet.in
mb96340 series 80 fme-mb96340 rev 10 external reset timing (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol pin value unit remarks min typ max reset input time t rstl rstx 500 - - ns 0.2 v cc rstx t rstl 0.2 v cc www.datasheet.in
mb96340 series fme-mb96340 rev 10 81 power on reset timing (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol pin value unit remarks min typ max power on rise time t r vcc 0.05 - 30 ms power off time t off vcc 1 - - ms 0.2 v t r 2.7v t off 0.2 v 0.2 v if the power supply is changed too rapidly, a power-on reset may occur. we recommend a smooth startup by restraining voltages when changing the power supply voltage during operation, as shown in the ?ure below. 3 v v cc v cc rising edge of 50 mv/ms maximum is allowed www.datasheet.in
mb96340 series 82 fme-mb96340 rev 10 external input timing note : relocated resource inputs have same characteristics (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol pin condition value unit used pin input func- tion min max input pulse width t inh t inl intn(_r) ? 200 ? ns external interrupt nmi(_r) nmi pnn_m 2*t clkp1 + 200 (t clkp1 =1/ f clkp1 ) ? ns general purpose io tinn(_r) reload timer ttgn(_r) ppg trigger input adtg(_r) ad converter trigger frckn(_r) free running timer external clock inn(_r) input capture v il v ih t inh v il v ih t inl external pin input www.datasheet.in
mb96340 series fme-mb96340 rev 10 83 external bus timing note: the values given below are for an i/o driving strength io drive = 5ma. if io drive is 2ma, all the maximum output timing described in the different tables must then be increased by 10ns. basic timing (t a =? 40 cto + 125 c, v cc = 5.0 v 10 % ,v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value unit remarks min max eclk t cyc eclk ? 25 ? ns t chcl t cyc /2-5 t cyc /2+5 t clch t cyc /2-5 t cyc /2+5 eclk ubx/ lbx / csn time t chcbh csn, ubx, lbx, eclk ? -20 20 ns t chcbl -20 20 t clcbh -20 20 t clcbl -20 20 eclk ale time t chlh ale, eclk ? -10 10 ns t chll -10 10 t cllh -10 10 t clll -10 10 eclk address valid time t chav a[23:16], eclk ? -15 15 ns t clav -15 15 t cladv ad[15:0], eclk ? -15 15 ns t chadv -15 15 eclk rdx /wrx time t chrwh rdx, wrx, wrlx,wrhx, eclk ? -10 10 ns t chrwl -10 10 t clrwh -10 10 t clrwl -10 10 www.datasheet.in
mb96340 series 84 fme-mb96340 rev 10 (t a =? 40 cto + 125 c, v cc = 3.0 to 4.5v, v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value unit remarks min max eclk t cyc eclk ? 30 ? ns t chcl t cyc /2-8 t cyc /2+8 t clch t cyc /2-8 t cyc /2+8 eclk ubx/ lbx / csn time t chcbh csn, ubx, lbx, eclk ? -25 25 ns t chcbl -25 25 t clcbh -25 25 t clcbl -25 25 eclk ale time t chlh ale, eclk ? -15 15 ns t chll -15 15 t cllh -15 15 t clll -15 15 eclk address valid time t chav a[23:16], eclk ? -20 20 ns t clav -20 20 t cladv ad[15:0], eclk ? -20 20 ns t chadv -20 20 eclk rdx /wrx time t chrwh rdx, wrx, wrlx, wrhx, eclk ? -15 15 ns t chrwl -15 15 t clrwh -15 15 t clrwl -15 15 www.datasheet.in
mb96340 series fme-mb96340 rev 10 85 eclk t cyc csn ale a[23:16] 0.2*vcc t chcl t chav t chcbl t chcbh lbx ubx t cllh t chll t chlh t clll t cladv ad[15:0] address t clav t chadv t clcbh t clcbl t chrwh t clrwh t clrwl t chrwl rdx wrx (wrlx, wrhx) 0.8*vcc t clch refer to the hardware manual for detailed timing charts www.datasheet.in
mb96340 series 86 fme-mb96340 rev 10 bus timing (read) (t a =? 40 cto + 125 c, v cc = 5.0 v 10 % ,v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter sym- bol pin conditions value unit remarks min max ale pulse width t lhll ale eacl:sts=0 and eacl:ace=0 t cyc /2 ? 5 ? ns eacl:sts=1 t cyc ? 5 ? eacl:sts=0 and eacl:ace=1 3t cyc /2 ? 5 ? valid address ? ale time t avll ale, a[23:16], eacl:sts=0 and eacl:ace=0 t cyc ? 15 ? ns eacl:sts=1 and eacl:ace=0 3t cyc /2 ? 15 ? eacl:sts=0 and eacl:ace=1 2t cyc ? 15 ? eacl:sts=1 and eacl:ace=1 5t cyc /2 ? 15 ? t advll ale,ad[15:0] eacl:sts=0 and eacl:ace=0 t cyc /2 ? 15 ? ns eacl:sts=1 and eacl:ace=0 t cyc ? 15 ? eacl:sts=0 and eacl:ace=1 3t cyc /2 ? 15 ? eacl:sts=1 and eacl:ace=1 2t cyc ? 15 ? ale ? address valid time t llax ale, ad[15:0] eacl:sts=0 t cyc /2 ? 15 ? ns eacl:sts=1 -15 ? valid address ? rdx time t avrl rdx, a[23:16] eacl:ace=0 3t cyc /2 ? 15 ? ns eacl:ace=1 5t cyc /2 ? 15 ? t advrl rdx, ad[15:0] eacl:ace=0 t cyc ? 15 ? ns eacl:ace=1 2t cyc ? 15 ? valid address ? valid data input t avdv a[23:16], ad[15:0] eacl:ace=0 ? 3t cyc ? 55 ns w/o cycle extension eacl:ace=1 ? 4t cyc ? 55 t advdv ad[15:0] eacl:ace=0 ? 5t cyc /2 ? 55 ns w/o cycle extension eacl:ace=1 ? 7t cyc /2 ? 55 rdx pulse width t rlrh rdx ? 3 t cyc /2 ? 5 ? ns w/o cycle extension rdx ? valid data input t rldv rdx, ad[15:0] ?? 3t cyc /2 ? 50 ns w/o cycle extension rdx ? data hold time t rhdx rdx, ad[15:0] ? 0 ? ns www.datasheet.in
mb96340 series fme-mb96340 rev 10 87 address valid ? data hold time t axdx a[23:16], ad[15:0] ? 0 ? ns rdx ? ale time t rhlh rdx, ale eacl:sts=1 and eacl:ace=1 3t cyc /2 ? 10 ? ns other ecl:sts, eacl:ace setting t cyc /2 ? 10 ? valid address ? eclk time t avch a[23:16], eclk ? t cyc ? 15 ? ns t advch ad[15:0], eclk t cyc /2 ? 15 ? rdx ? eclk time t rlch rdx, eclk ? t cyc /2 ? 10 ? ns ale ? rdx time t llrl ale, rdx eacl:sts=0 t cyc /2 ? 10 ? ns eacl:sts=1 ? 10 ? eclk ? valid data input t chdv ad[15:0], eclk ?? t cyc ? 50 ns (t a =? 40 cto + 125 c, v cc = 3.0 to 4.5v, v ss = 0.0 v, io drive = 5ma, c l = 50pf) parameter sym- bol pin conditions value unit remarks min max ale pulse width t lhll ale eacl:sts=0 and eacl:ace=0 t cyc /2 ? 8 ? ns eacl:sts=1 t cyc ? 8 ? eacl:sts=0 and eacl:ace=1 3t cyc /2 ? 8 ? valid address ? ale time t avll ale, a[23:16], eacl:sts=0 and eacl:ace=0 t cyc ? 20 ? ns eacl:sts=1 and eacl:ace=0 3t cyc /2 ? 20 ? eacl:sts=0 and eacl:ace=1 2t cyc ? 20 ? eacl:sts=1 and eacl:ace=1 5t cyc /2 ? 20 ? t advll ale, ad[15:0] eacl:sts=0 and eacl:ace=0 t cyc /2 ? 20 ? ns eacl:sts=1 and eacl:ace=0 t cyc ? 20 ? eacl:sts=0 and eacl:ace=1 3t cyc /2 ? 20 ? eacl:sts=1 and eacl:ace=1 2t cyc ? 20 ? ale ? address valid time t llax ale, ad[15:0] eacl:sts=0 t cyc /2 ? 20 ? ns eacl:sts=1 -20 ? (t a =? 40 cto + 125 c, v cc = 5.0 v 10 % ,v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter sym- bol pin conditions value unit remarks min max www.datasheet.in
mb96340 series 88 fme-mb96340 rev 10 valid address ? rdx time t avrl rdx, a[23:16] eacl:ace=0 3t cyc /2 ? 20 ? ns eacl:ace=1 5t cyc /2 ? 20 ? t advrl rdx, ad[15:0] eacl:ace=0 t cyc ? 20 ? ns eacl:ace=1 2t cyc ? 20 ? valid address ? valid data input t avdv a[23:16], ad[15:0] eacl:ace=0 ? 3t cyc ? 60 ns w/o cycle extension eacl:ace=1 ? 4t cyc ? 60 t advdv ad[15:0] eacl:ace=0 ? 5t cyc /2 ? 60 ns w/o cycle extension eacl:ace=1 ? 7t cyc /2 ? 60 rdx pulse width t rlrh rdx ? 3t cyc /2 ? 8 ? ns w/o cycle extension rdx ? valid data input t rldv rdx, ad[15:0] ?? 3t cyc /2 ? 55 ns w/o cycle extension rdx ? data hold time t rhdx rdx, ad[15:0] ? 0 ? ns address valid ? data hold time t axdx a[23:16] ? 0 ? ns rdx ? ale time t rhlh rdx, ale eacl:sts=1 and eacl:ace=1 3t cyc /2 ? 15 ? ns other ecl:sts, eacl:ace setting t cyc /2 ? 15 ? valid address ? eclk time t avch a[23:16], eclk ? t cyc ? 20 ? ns t advch ad[15:0], eclk t cyc /2 ? 20 ? rdx ? eclk time t rlch rdx, eclk ? t cyc /2 ? 15 ? ns ale ? rdx time t llrl ale, rdx eacl:sts=0 t cyc /2 ? 15 ? ns eacl:sts=1 ? 15 ? eclk ? valid data input t chdv ad[15:0], eclk ?? t cyc ? 55 ns (t a =? 40 cto + 125 c, v cc = 3.0 to 4.5v, v ss = 0.0 v, io drive = 5ma, c l = 50pf) parameter sym- bol pin conditions value unit remarks min max www.datasheet.in
mb96340 series fme-mb96340 rev 10 89 . bus timing (write) (t a =? 40 cto + 125 c, v cc = 5.0 v 10 % ,v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value unit remarks min max valid address ? wrx time t avwl wrx, wrlx, wrhx, a[23:16] eacl:ace=0 3t cyc /2 ? 15 ? ns eacl:ace=1 5t cyc /2 ? 15 ? t advwl wrx, wrlx, wrhx, ad[15:0] eacl:ace=0 t cyc ? 15 ? ns eacl:ace=1 2t cyc ? 15 ? wrx pulse width t wlwh wrx, wrxl, wrhx ? t cyc ? 5 ? ns w/o cycle extension valid data output ? wrx time t dvwh wrx, wrlx, wrhx, ad[15:0] ? t cyc ? 20 ? ns w/o cycle extension a[23:16] ad[15:0] address v il v ih v ih v il read data t rhdx t rldv t advdv eclk t advch 0.8*vcc t rlch ale t lhll t rhlh 0.2*v cc t llax t advll rdx t llrl t rlrh t advrl t avch t avll t avdv t avrl t chdv t axdx refer to the hardware manual for detailed timing charts www.datasheet.in
mb96340 series 90 fme-mb96340 rev 10 wrx ? data hold time t whdx wrx, wrlx, wrhx, ad[15:0] ? t cyc /2 ? 15 ? ns wrx ? address valid time t whax wrx, wrlx, wrhx, a[23:16] ? t cyc /2 ? 15 ? ns wrx ? ale time t whlh wrx, wrlx, wrhx, ale ebm:ace=1 and eacl:sts=1 2t cyc ? 10 ? ns other ebm:ace and eacl:sts setting t cyc ? 10 ? wrx ? eclk time t wlch wrx, wrlx, wrhx, eclk ? t cyc /2 ? 10 ? ns csn ? wrx time t cslwl wrx, wrlx, wrhx, csn eacl:ace=0 ? 3t cyc /2 ? 15 ns eacl:ace=1 ? 5t cyc /2 ? 15 wrx ? csn time t whcsh wrx, wrlx, wrhx, csn ? t cyc /2 ? 15 ? ns (t a =? 40 cto + 125 c, v cc = 3.0 to 4.5v, v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value unit remarks min max valid address ? wrx time t avwl wrx, wrlx, wrhx, a[23:16] eacl:ace=0 3t cyc /2 ? 20 ? ns eacl:ace=1 5t cyc /2 ? 20 ? t advwl wrx, wrlx, wrhx, ad[15:0] eacl:ace=0 t cyc ? 20 ? ns eacl:ace=1 2t cyc ? 20 ? wrx pulse width t wlwh wrx, wrxl, wrhx ? t cyc ? 8 ? ns w/o cycle extension valid data output ? wrx time t dvwh wrx, wrlx, wrhx, ad[15:0] ? t cyc ? 25 ? ns w/o cycle extension wrx ? data hold time t whdx wrx, wrlx, wrhx, ad[15:0] ? t cyc /2 ? 20 ? ns wrx ? address valid time t whax wrx, wrlx, wrhx, a[23:16] ? t cyc /2 ? 20 ? ns (t a =? 40 cto + 125 c, v cc = 5.0 v 10 % ,v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value unit remarks min max www.datasheet.in
mb96340 series fme-mb96340 rev 10 91 . wrx ? ale time t whlh wrx, wrlx, wrhx, ale ebm:ace=1 and eacl:sts=1 2t cyc ? 15 ? ns other ebm:ace and eacl:sts setting t cyc ? 15 ? wrx ? eclk time t wlch wrx, wrlx, wrhx, eclk ? t cyc /2 ? 15 ? ns csn ? wrx time t cslwl wrx, wrlx, wrhx, csn eacl:ace=0 ? 3t cyc /2 ? 20 ns eacl:ace=1 ? 5t cyc /2 ? 20 wrx ? csn time t whcsh wrx, wrlx, wrhx, csn ? t cyc /2 ? 20 ? ns (t a =? 40 cto + 125 c, v cc = 3.0 to 4.5v, v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value unit remarks min max eclk t wlch 0.8*v cc ale t whlh wrx (wrlx, wrhx) t wlwh t advwl a[23:16] t whax ad[15:0] address write data t dvwh t whdx csn t whcsh t avwl t cslwl 0.2*v cc refer to the hardware manual for detailed timing charts www.datasheet.in
mb96340 series 92 fme-mb96340 rev 10 ready input timing note : if the rdy setup time is insuf?ient, use the auto-ready function. hold timing (t a =? 40 cto + 125 c, v cc = 5.0 v 10 % ,v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin test condition rated value units remarks min max rdy setup time t ryhs rdy ? 35 ? ns rdy hold time t ryhh rdy 0 ? ns (t a =? 40 cto + 125 c, v cc = 3.0 to 4.5v, v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin test condition rated value units remarks min max rdy setup time t ryhs rdy ? 45 ? ns rdy hold time t ryhh rdy 0 ? ns (t a =? 40 cto + 125 c, v cc = 5.0 v 10 % ,v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value units remarks min max pin floating ? hakx time t xhal hakx ? t cyc ? 20 t cyc + 20 ns hakx time ? pin valid time t hahv hakx t cyc ? 20 t cyc +20 ns (t a =? 40 cto + 125 c, v cc = 3.0 to 4.5v, v ss = 0.0 v, io drive =5ma,c l = 50pf) parameter symbol pin condition value units remarks min max pin floating ? hakx time t xhal hakx ? t cyc ? 25 t cyc +25 ns hakx time ? pin valid time t hahv hakx t cyc ? 25 t cyc +25 ns eclk rdy when wait is not used. v ih v ih t ryhh rdy when wait is used. t ryhs v il 0.8*v cc refer to the hardware manual for detailed timing charts www.datasheet.in
mb96340 series fme-mb96340 rev 10 93 hakx each pin high-z t hahv t xhal 0.8*v cc 0.2*v cc 0.8*v cc 0.2*v cc refer to the hardware manual for detailed timing charts www.datasheet.in
mb96340 series 94 fme-mb96340 rev 10 usart timing warning: the values given below are for an i/o driving strength io drive = 5ma. if io drive is 2ma, all the maximum output timing described in the different tables must then be increased by 10ns. notes: ? ac characteristic in clk synchronized mode. ? c l is the load capacity value of pins when testing. ? depending on the used machine clock frequency, the maximum possible baud rate can be limited by some parameters. these parameters are shown in ?b96300 super series hardware manual ? t clkp1 is the cycle time of the peripheral clock 1 (clkp1), unit : ns *1: parameter n depends on t scyci and can be calculated as follows: if t scyci = 2*k*t clkp1 , then n = k, where k is an integer > 2 if t scyci = (2*k+1)*t clkp1 , then n = k+1, where k is an integer > 1 examples: (t a = -40?c to 125?c, v cc = 3.0v to 5.5v, v ss = av ss = 0v, io drive = 5ma, c l = 50pf) parameter symbol pin condition v cc =av cc = 4.5v to 5.5v v cc =av cc = 3.0v to 4.5v unit min max min max serial clock cycle time t scyci sckn internal shift clock mode 4 t clkp1 ? 4 t clkp1 ? ns sck sot delay time t slovi sckn, sotn -20 + 20 -30 + 30 ns sot sck delay time t ovshi sckn, sotn n*t clkp1 - 20 *1 ? n*t clkp1 - 30 *1 ? ns valid sin sck t ivshi sckn, sinn t clkp1 + 45 ? t clkp1 + 55 ? ns sck valid sin hold time t shixi sckn, sinn 0 ? 0 ? ns serial clock ??pulse width t slshe sckn external shift clock mode t clkp1 + 10 ? t clkp1 + 10 ? ns serial clock ??pulse width t shsle sckn t clkp1 + 10 ? t clkp1 + 10 ? ns sck sot delay time t slove sckn, sotn ? 2 t clkp1 + 45 ? 2 t clkp1 + 55 ns valid sin sck t ivshe sckn, sinn t clkp1 /2 + 10 ? t clkp1 /2 + 10 ? ns sck valid sin hold time t shixe sckn, sinn t clkp1 + 10 ? t clkp1 + 10 ? ns sck fall time t fe sckn ? 20 ? 20 ns sck rise time t re sckn ? 20 ? 20 ns t scyci n 4*t clkp1 2 5*t clkp1, 6*t clkp1 3 7*t clkp1, 8*t clkp1 4 ... ... www.datasheet.in
mb96340 series fme-mb96340 rev 10 95 internal shift clock mode sot t slovi sin v il v ih t ivshi v il v ih t shixi t ovshi sck for escr:sces = 0 0.8*v cc t scyci sck for escr:sces = 1 0.8*v cc 0.8*v cc 0.2*v cc 0.2*v cc 0.2*v cc 0.8*v cc 0.2*v cc external shift clock mode t fe v il v il v il v il sot t slove sin v il v ih t ivshe v il v ih t shixe v ih t re v ih t slshe v il v ih t shsle v ih v ih sck for escr:sces = 0 sck for escr:sces = 1 0.8*v cc 0.2*v cc www.datasheet.in
mb96340 series 96 fme-mb96340 rev 10 i 2 c timing *1 : for use at over 100 khz, set the peripheral clock 1 to at least 6 mhz. *2 : c b = capacitance of one bus line in pf. *3 : t clkp1 is the cycle time of the periperal clock clkp1. ? oh = 0.7 * v cc ? ol = 0.3 * v cc cmos hysteresis 0.7/0.3 input selected (t a = -40?c to 125?c, v cc = av cc = 3.0v to 5.5v,v ss = av ss =0v) parameter symbol standard-mode fast-mode* 1 unit min max min max scl clock frequency f scl 0 100 0 400 khz hold time (repeated) start condition sda scl t hdsta 4.0 ? 0.6 ? s ??width of the scl clock t low 4.7 ? 1.3 ? s ??width of the scl clock t high 4.0 ? 0.6 ? s set-up time for a repeated start condition scl sda t susta 4.7 ? 0.6 ? s data hold time scl sda t hddat 0 3.45 0 0.9 s data set-up time sda scl t sudat 250 ? 100 ? ns set-up time for stop condition scl sda t susto 4.0 ? 0.6 ? s bus free time between a stop and start condition t bus 4.7 ? 1.3 ? s output fall time from 0.7*vcc to 0.3*vcc with a bus capacitance from 10 pf to 400 pf t of 20 + 0.1*c b * 2 250 20 + 0.1*c b * 2 250 ns capacitive load for each bus line c b ? 400 ? 400 pf pulse width of spikes which will be sup- pressed by input noise filter t sp n/a n/a 0 1*t clkp1 * 3 ns sda scl t low t sudat t hdsta t bus t hdsta t hddat t high t susta t susto www.datasheet.in
mb96340 series fme-mb96340 rev 10 97 5. analog digital converter note: the accuracy gets worse as |avrh - avrl| becomes smaller. (t a = -40 ?c to +125 ?c, 3.0 v avrh - avrl, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter symbol pin value unit remarks min typ max resolution - - - - 10 bit total error - - - - 3 lsb nonlinearity error - - - - 2.5 lsb differential nonlinearity error -- - - 1.9 lsb zero transition voltage v ot ann avrl - 1.5 lsb avrl+ 0.5 lsb avrl + 2.5 lsb v full scale transition voltage v fst ann avrh - 3.5 lsb avrh - 1.5 lsb avrh + 0.5 lsb v compare time - - 1.0 - 16,500 s 4.5v v cc 5.5v 2.0 - - s 3.0v v cc < 4.5v sampling time - - 0.5 - - s 4.5v v cc 5.5v 1.2 - - s 3.0v v cc < 4.5v analog input leakage current (during conver- sion) i ain ann -1 - +1 a t a 105 ?c, av ss , avrl < v i < av cc , avrh -1.2 - +1.2 a 105 ?c < t a 125 ?c, av ss , avrl < v i < av cc , avrh analog input voltage range v ain ann avrl - avrh v reference voltage range avrh avrh/ avrh2 0.75 avcc - avcc v avrl avrl av ss - 0.25 av cc v power supply current i a avcc - 2.5 5 ma a/d converter active i ah avcc - - 5 a a/d converter not op- erated reference voltage cur- rent i r avrh/ avrl - 0.7 1 ma a/d converter active i rh avrh/ avrl --5 a a/d converter not op- erated offset between input channels - ann - - 4 lsb www.datasheet.in
mb96340 series 98 fme-mb96340 rev 10 definition of a/d converter terms resolution: analog variation that is recognized by an a/d converter. t otal error : difference between the actual value and the ideal value. the total error includes zero transition error, full-scale transition error and nonlinearity error. nonlinear ity error : deviation between a line across zero-transition line (?0 0000 0000 <--> ?0 0000 0001? and full-scale transition line (?1 1111 1110?<--> ?1 1111 1111? and actual conversion characteristics. diff erential nonlinear ity error : deviation of input voltage, which is required for changing output code by 1 lsb, from an ideal value. zero reading v oltage: input voltage which results in the minimum conversion value. full scale reading v oltage: input voltage which results in the maximum conversion value. 3ff 3fe 3fd 004 003 002 001 avrl avrh v nt 1.5 lsb 0.5 lsb {1 lsb (n ? 1) + 0.5 lsb} actual conversion characteristics (actually-measured value) actual conversion characteristics ideal characteristics digital output analog input total error of digital output ? = v nt ? {1 lsb (n ? 1) + 0.5 lsb} 1 lsb [lsb] 1 lsb = (ideal value) avrh ? avrl 1024 [v] v ot (ideal value) = avrl + 0.5 lsb [v] v fst (ideal value) = avrh ? 1.5 lsb [v] v nt : a voltage at which digital output transitions from (n ? 1) to n. total error n: a/d converter digital output value www.datasheet.in
mb96340 series fme-mb96340 rev 10 99 3ff 3fe 3fd 004 003 002 001 avrl avrh avrl avrh n + 1 n n ? 1 n ? 2 v ot ( actual measurement value ) {1 lsb (n ? 1) + v ot } actual conversion characteristics v fst (actual measurement value) v nt (actual measurement value) actual conversion characteristics ideal characteristics actual conversion characteristics actual conversion characteristics ideal characteristics digital output digital output analog input analog input v nt (actual measurement value) v (n + 1) t (actual measurement value) nonlinearity error differential nonlinearity error differential nonlinearity error of digital output n = 1 lsb = nonlinearity error of digital output n = v nt ? {1 lsb (n ? 1) + v ot } 1 lsb [lsb] v ( n+1 ) t ? v nt 1 lsb ? 1 lsb [lsb] v fst ? v ot 1022 [v] n : a/d converter digital output value v ot : voltage at which digital output transits from ?00 h ?to ?01 h . v fst : voltage at which digital output transits from ?fe h ?to ?ff h . www.datasheet.in
mb96340 series 100 fme-mb96340 rev 10 accuracy and setting of the a/d converter sampling time if the external impedance is too high or the sampling time too short, the analog voltage charged to the internal sample and hold capacitor is insuf?ient, adversely affecting the a/d conversion precision. to satisfy the a/d conversion precision, a suf?ient sampling time must be selected. the required sampling time depends on the external driving impedance r ext , the board capacitance of the a/d converter input pin c ext and the av cc voltage level. the following replacement model can be used for the calculation: the sampling time should be set to minimum ? ? the following approximation formula for the replacement model above can be used: t samp [min] = 7 (r ext (c ext + c in ) + (r ext + r adc ) c adc ) do not select a sampling time below the absolute minimum permitted value (0.5 s for 4.5v av cc 5.5v; 1.2 s for 3.0v av cc < 4.5v). if the sampling time cannot be suf?ient, connect a capacitor of about 0.1 f to the analog input pin. in this case the internal sampling capacitance c adc will be charged out of this external capacitance. a big external driving impedance also adversely affects the a/d conversion precision due to the pin input leakage current i il (static current before the sampling switch) or the analog input leakage current i ain (total leakage current of pin input and comparator during sampling). the effect of the pin input leakage current i il cannot be compensated by an external capacitor. the accuracy gets worse as |avrh - avrl| becomes smaller. comparator sampling switch r adc c adc analog r ext c ext input mcu source r ext : external driving impedance c ext : capacitance of pcb at a/d converter input r adc : resistance within mcu: 2.6k ? (max) for 4.5v av cc 5.5v 12k ? (max) for 3.0v av cc < 4.5v c adc : sampling capacitance within mcu: 10pf (max) c in c in : capacitance of mcu input pin: 15pf (max) www.datasheet.in
mb96340 series fme-mb96340 rev 10 101 6. alarm comparator (t a = -40 ?c to +125 ?c, v cc = av cc = 3.0v - 5.5v, v ss = av ss = 0v) parameter symbol pin value unit remarks min typ max power supply current i a5almf av cc -2545 a alarm comparator enabled in fast mode (one channel) i a5alms -713 a alarm comparator enabled in slow mode (one channel) i a5almh --5 a alarm comparator disabled alarm pin input cur- rent i alin alarm0, alarm1 -1 - +1 at a = 25 ?c -3 - +3 at a = 125 ?c alarm pin input volt- age range v alin 0-av cc v external low threshold high->low transition v evtl(h->l) 0.36 * av cc -0.25 0.36 * av cc -0.1 -v intref = 0 external low threshold low->high transition v evtl(l->h) - 0.36 * av cc +0.1 0.36 * av cc +0.25 v external high threshold high->low transition v evth(h->l) 0.78 * av cc -0.25 0.78 * av cc -0.1 -v external high threshold low->high transition v evth(l->h) 0.78 * av cc +0.1 0.78 * av cc +0.25 v internal low threshold high->low transition v ivtl(h->l) 0.9 1.1 - v intref = 1 internal low threshold low->high transition v ivtl(l->h) - 1.3 1.55 v internal high threshold high->low transition v ivth(h->l) 2.2 2.4 - v internal high threshold low->high transition v ivth(l->h) - 2.6 2.85 v switching hysteresis v hys 50 - 300 mv comparison time t compf - 0.1 1 s cmd = 1 (fast) t comps -110 s cmd = 0 (slow) power-up stabilization time after enabling alarm comparator t pd - 1 10 ms threshold levels speci?d above are not guaranteed within this time slow/fast mode transi- tion time t cmd - 100 500 s www.datasheet.in
mb96340 series 102 fme-mb96340 rev 10 comparator output v xvtx(l->h) v hys v alin h l v xvtx(h->l) www.datasheet.in
mb96340 series fme-mb96340 rev 10 103 7. low voltage detector characteristics *1: valid for all devices except devices listed under ?2 *2: valid for: mb96f345 cilcr:lvl[3:0] are the low voltage detector level select bits of the cilcr register. for correct detection, the slope of the voltage level must satisfy . faster variations are regarded as noise and may not be detected. the functional operation of the mcu is guaranteed down to the minimum low voltage detection level of ?evel 0 (v dl0_min ). the electrical characteristics however are only valid in the speci?d range (usually down to 3.0v). (t a = -40 ?c to +125 ?c, v cc = av cc = 3.0v - 5.5v, v ss = av ss = 0v) parameter symbol value *1 value *2 unit remarks min max min max stabilization time t lvdstab - 75 - 110 s after power-up or change of detection level level 0 v dl0 2.7 2.9 2.5 2.9 v cilcr:lvl[3:0]=?000 level 1 v dl1 2.9 3.1 2.8 3.2 v cilcr:lvl[3:0]=?001 level 2 v dl2 3.1 3.3 3 3.4 v cilcr:lvl[3:0]=?010 level 3 v dl3 3.5 3.75 3.35 3.8 v cilcr:lvl[3:0]=?011 level 4 v dl4 3.6 3.85 3.5 3.95 v cilcr:lvl[3:0]=?100 level 5 v dl5 3.7 3.95 3.6 4.1 v cilcr:lvl[3:0]=?101 level 6 v dl6 3.8 4.05 3.7 4.2 v cilcr:lvl[3:0]=?110 level 7 v dl7 3.9 4.15 3.8 4.3 v cilcr:lvl[3:0]=?111 level 8 v dl8 4.0 4.25 3.9 4.4 v cilcr:lvl[3:0]=?000 level 9 v dl9 4.1 4.35 3.95 4.5 v cilcr:lvl[3:0]=?001 level 10 v dl10 not used not used level 11 v dl11 not used not used level 12 v dl12 not used 2.6 3 v cilcr:lvl[3:0]=?100 level 13 v dl13 not used not used level 14 v dl14 not used not used level 15 v dl15 not used not used t d d v 0.004 v s ----- www.datasheet.in
mb96340 series 104 fme-mb96340 rev 10 low voltage detector operation in the following ?ure, the occurrence of a low voltage condition is illustrated. for a detailed description of the reset and startup behavior, please refer to the corresponding hardware manual chapter. voltage [v] time [s] v cc v dlx, min v dlx, max dv dt low voltage reset assertion normal operation power reset extension time www.datasheet.in
mb96340 series fme-mb96340 rev 10 105 8. flash memory program/erase characteristics *1: this value was converted from the results of evaluating the reliability of the technology (using arrhenius equation to convert high temperature measurements into normalized value at 85 o c) (t a = -40?c to 105?c, v cc = av cc = 3.0v to 5.5v, v ss = av ss = 0v) parameter value unit remarks min typ max sector erase time program/data flash (main flash) - 0.9 3.6 s without erasure pre-program- ming time sector erase time data flash - 0.5 2 s without erasure pre-program- ming time - 0.8 3.6 s including erasure pre-program- ming time chip erase time program/data flash (main flash) - n*0.9 n*3.6 s without erasure pre-program- ming time (n is the number of flash sector of the device) chip erase time data flash - 2.5 10 s without erasure pre-program- ming time - 3.7 16.4 s including erasure pre-program- ming time word (16-bit width) programming time program/data flash (main flash) - 23 370 us without overhead time for sub- mitting write command byte (8-bit width) programming time data flash - 15 100 us without overhead time for sub- mitting write command program/erase cycle 10 000 - - cycle 100 000 program/erase cycles are under evaluation by fujitsu microelectronics flash data retention time 20 - - year *1 www.datasheet.in
mb96340 series 106 fme-mb96340 rev 10 example characteristics 1. temperature dependency of power supply currents the following diagrams show the current consumption of samples with typical wafer process parameters in differ- ent operation modes. common condition for all operation modes: ? cc = av cc = 5.0v main clock = 4mhz external clock sub clock = 32khz external clock operation mode details: mode name details pll run 56 pll run mode current i ccpll with the following settings: ? clks1 = f clks2 = f clkb = f clkp1 = 56mhz ? clkp2 = 28mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) 2 flash/rom wait states (mtcra=233a h ) rc oscillator and sub oscillator stopped pll run 48 pll run mode current i ccpll with the following settings: ? clks1 = f clks2 = 96mhz ? clkb = f clkp1 = 48mhz ? clkp2 = 24mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) 1 flash/rom wait states (mtcra=6b09 h ) rc oscillator and sub oscillator stopped pll run 40 pll run mode current i ccpll with the following settings: ? clks1 = f clks2 = 80mhz ? clkb = f clkp1 = 40mhz ? clkp2 = 20mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) 1 flash/rom wait states (mtcra=6b09 h ) rc oscillator and sub oscillator stopped pll run 36 pll run mode current i ccpll with the following settings: ? clks1 = f clks2 = 72mhz ? clkb = f clkp1 = 36mhz ? clkp2 = 18mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) 1 flash/rom wait states (mtcra=6b09 h ) rc oscillator and sub oscillator stopped www.datasheet.in
mb96340 series fme-mb96340 rev 10 107 pll run 24 pll run mode current i ccpll with the following settings: ? clks1 = f clks2 = 48mhz ? clkb = f clkp1 = f clkp2 = 24mhz regulator in high power mode core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) 0 flash/rom wait states (mtcra=2208 h ) rc oscillator and sub oscillator stopped main run main run mode current i ccmain with the following settings: ? clks1 = f clks2 = f clkb = f clkp1 = f clkp2 = 4mhz regulator in high power mode core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) 1 flash/rom wait states (mtcra=0239 h ) pll, rc oscillator and sub oscillator stopped rc run 2m rc run mode current i ccrch with the following settings: rc oscillator set to 2mhz (ckfcr:rcfs = 1) ? clks1 = f clks2 = f clkb = f clkp1 = f clkp2 = 2mhz regulator in high power mode core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) 1 flash/rom wait states (mtcra=0239 h ) pll, main oscillator and sub oscillator stopped rc run 100k rc run mode current i ccrcl with the following settings: rc oscillator set to 100khz (ckfcr:rcfs = 0) ? clks1 = f clks2 = f clkb = f clkp1 = f clkp2 = 100khz regulator in low power mode a (smcr:lpms = 1) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) 1 flash/rom wait states (mtcra=0239 h ) pll, main oscillator and sub oscillator stopped sub run sub run mode current i ccsub with the following settings: ? clks1 = f clks2 = f clkb = f clkp1 = f clkp2 = 32khz regulator in low power mode a (by hardware) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) 1 flash/rom wait states (mtcra=0239 h ) pll, rc oscillator and main oscillator stopped pll sleep 56 pll sleep mode current i ccspll with the following settings: ? clks1 = f clks2 = f clkp1 = 56mhz ? clkp2 = 28mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) rc oscillator and sub oscillator stopped mode name details www.datasheet.in
mb96340 series 108 fme-mb96340 rev 10 pll sleep 48 pll sleep mode current i ccspll with the following settings: ? clks1 = f clks2 = 96mhz ? clkp1 = 48mhz ? clkp2 = 24mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) rc oscillator and sub oscillator stopped pll sleep 40 pll sleep mode current i ccspll with the following settings: ? clks1 = f clks2 = 80mhz ? clkp1 = 40mhz ? clkp2 = 20mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) rc oscillator and sub oscillator stopped pll sleep 36 pll sleep mode current i ccspll with the following settings: ? clks1 = f clks2 = 72mhz ? clkp1 = 36mhz ? clkp2 = 18mhz regulator in high power mode core voltage at 1.9v (vrcr:hpm[1:0] = 11 b ) rc oscillator and sub oscillator stopped pll sleep 24 pll sleep mode current i ccspll with the following settings: ? clks1 = f clks2 = 48mhz ? clkp1 = f clkp2 = 24mhz regulator in high power mode core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) rc oscillator and sub oscillator stopped main sleep main sleep mode current i ccsmain with the following settings: ? clks1 = f clks2 = f clkp1 = f clkp2 = 4mhz regulator in high power mode core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) pll, rc oscillator and sub oscillator stopped rc sleep 2m rc sleep mode current i ccsrch with the following settings: rc oscillator set to 2mhz (ckfcr:rcfs = 1) ? clks1 = f clks2 = f clkp1 = f clkp2 = 2mhz regulator in high power mode core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) pll, main oscillator and sub oscillator stopped rc sleep 100k rc sleep mode current i ccsrcl with the following settings: rc oscillator set to 100khz (ckfcr:rcfs = 0) ? clks1 = f clks2 = f clkp1 = f clkp2 = 100khz regulator in low power mode a (smcr:lpmss = 1) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) pll, main oscillator and sub oscillator stopped mode name details www.datasheet.in
mb96340 series fme-mb96340 rev 10 109 sub sleep sub sleep mode current i ccssub with the following settings: ? clks1 = f clks2 = f clkp1 = f clkp2 = 32khz regulator in low power mode a (by hardware) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) pll, rc oscillator and main oscillator stopped pll timer 48 pll timer mode current i cctpll with the following settings: ? clks1 = f clks2 = 48mhz regulator in high power mode core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) rc oscillator and sub oscillator stopped main timer main timer mode current i cctmain with the following settings: ? clks1 = f clks2 = 4mhz regulator in low power mode a (smcr:lpmss = 1) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) pll, rc oscillator and sub oscillator stopped rc timer 2m rc timer mode current i cctrch with the following settings: rc oscillator set to 2mhz (ckfcr:rcfs = 1) ? clks1 = f clks2 = 2mhz regulator in low power mode a (smcr:lpmss = 1) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) pll, main oscillator and sub oscillator stopped rc timer 100k rc timer mode current i cctrcl with the following settings: rc oscillator set to 100khz (ckfcr:rcfs = 0) ? clks1 = f clks2 = 100khz regulator in low power mode a (smcr:lpmss = 1) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) pll, main oscillator and sub oscillator stopped sub timer sub timer mode current i cctsub with the following settings: ? clks1 = f clks2 = 32khz regulator in low power mode a (by hardware) core voltage at 1.8v (vrcr:lpma[2:0] = 110 b ) pll, rc oscillator and main oscillator stopped stop 1.8v stop mode current i cch with the following settings: regulator in low power mode b (by hardware) core voltage at 1.8v (vrcr:lpmb[2:0] = 110 b ) stop 1.2v stop mode current i cch with the following settings: regulator in low power mode b (by hardware) core voltage at 1.2v (vrcr:lpmb[2:0] = 000 b ) mode name details www.datasheet.in
mb96340 series 110 fme-mb96340 rev 10 MB96345/346 pll run and sleep mode currents MB96345/346 operation modes with medium currents 0 5 10 15 20 25 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] pll sleep 24 pll sleep 56 pll sleep 48 pll run 24 pll run 56 pll run 48 0 0.5 1 1.5 2 2.5 3 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] rc sleep 2m main sleep pll timer 48 rc run 2m main run www.datasheet.in
mb96340 series fme-mb96340 rev 10 111 MB96345/346 low power mode currents mb96f345 pll run and sleep mode currents 0.01 0.1 1 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] stop 1.2v stop 1.8v rc timer 100k sub timer sub sleep sub run rc sleep 100k rc timer 2m rc run 100k main timer 0 10 20 30 40 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] pll sleep 24 pll sleep 40 pll run 24 pll run 40 www.datasheet.in
mb96340 series 112 fme-mb96340 rev 10 mb96f345 operation modes with medium currents mb96f345 low power mode currents 0 1 2 3 4 5 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] rc sleep 2m main sleep pll timer 48 rc run 2m main run 0.001 0.01 0.1 1 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] stop 1.2v stop 1.8v rc timer 100k sub timer sub sleep sub run rc sleep 100k rc timer 2m rc run 100k main timer www.datasheet.in
mb96340 series fme-mb96340 rev 10 113 mb96f346/f347/f348y/r/a pll run and sleep mode currents mb96f346/f347/f348y/r/a operation modes with medium currents 0 10 20 30 40 50 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] pll sleep 24 pll sleep 56 pll sleep 36 pll run 24 pll run 56 pll run 36 0 1 2 3 4 5 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] rc sleep 2m main sleep pll timer 48 rc run 2m main run www.datasheet.in
mb96340 series 114 fme-mb96340 rev 10 mb96f346/f347/f348y/r/a low power mode currents mb96f348t/h/c pll run and sleep mode currents 0.01 0.1 1 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] stop 1.2v stop 1.8v rc timer 100k sub timer sub sleep sub run rc sleep 100k rc timer 2m rc run 100k main timer 0 10 20 30 40 50 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] pll sleep 24 pll sleep 56 pll sleep 48 pll run 24 pll run 56 pll run 48 www.datasheet.in
mb96340 series fme-mb96340 rev 10 115 mb96f348t/h/c operation modes with medium currents mb96f348t/h/c low power mode currents 0 1 2 3 4 5 6 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] rc sleep 2m main sleep pll timer 48 rc run 2m main run 0.001 0.01 0.1 1 -60 -40 -20 0 20 40 60 80 100 120 ta [?c] icc[ma] stop 1.2v stop 1.8v rc timer 100k sub timer sub sleep sub run rc sleep 100k rc timer 2m rc run 100k main timer www.datasheet.in
mb96340 series 116 fme-mb96340 rev 10 2. frequency dependency of power supply currents in pll run mode the following diagrams show the current consumption of samples with typical wafer process parameters in pll run mode at different frequencies and flash timing settings. measurement conditions: ? cc = av cc = 5.0v ta = 25?c ? clks1 = f clkb or f clks1 = 2*f clkb as described in diagram ? clks2 = f clks1 ? clkp1 = f clkb ? clkp2 = f clkb /2 core voltage at 1.8v (vrcr:hpm[1:0] = 10 b ) or 1.9v (vrcr:hpm[1:0] = 11 b ) as described in diagram main clock = 4mhz external clock flash memory timing settings: mtcra=2128 h /2208 h (0 flash wait states, f clks1 = 2*f clkb ) mtcra=0239 h /2129 h (1 flash wait state, f clks1 = f clkb ) mtcra=4c09 h /6b09 h (1 flash wait state, f clks1 = 2*f clkb ) mtcra=233a h (2 flash wait states, f clks1 = f clkb ) average flash access rate (number of read accesses to the flash per clkb clock cycle, no buffer hit): 0 flash wait states: 0.5 1 flash wait states: 0.33 2 flash wait states: 0.25 mb96f345 pll run mode currents 0 5 10 15 20 25 30 35 40 0 4 8 1216202428323640 clkb/clkp1 (mhz) iccpll (ma) 1 flash wait state (clks1=2*clkb, 1.9v) 1 flash wait state (clks1=2*clkb, 1.8v) 0 flash wait states (clks1=2*clkb, 1.8v) 1 flash wait state (clks1=clkb, 1.8v) 2 flash wait states (clks1=clkb, 1.8v) 2 flash wait states (clks1=clkb, 1.9v) : specified in "dc characteristics" www.datasheet.in
mb96340 series fme-mb96340 rev 10 117 mb96f346/f347/f348y/r/a pll run mode currents mb96f348t/h/c pll run mode currents 0 5 10 15 20 25 30 35 40 45 50 0 4 8 121620242832364044485256 clkb/clkp1 (mhz) iccpll (ma) 1 flash wait state (clks1=2*clkb, 1.9v) 1 flash wait state (clks1=2*clkb, 1.8v) 0 flash wait states (clks1=2*clkb, 1.8v) 1 flash wait state (clks1=clkb, 1.8v) 2 flash wait states (clks1=clkb, 1.8v) 2 flash wait states (clks1=clkb, 1.9v) : specified in "dc characteristics" 0 5 10 15 20 25 30 35 40 45 50 0 4 8 121620242832364044485256 clkb/clkp1 (mhz) iccpll (ma) 1 flash wait state (clks1=2*clkb, 1.9v) 1 flash wait state (clks1=2*clkb, 1.8v) 0 flash wait states (clks1=2*clkb, 1.8v) 1 flash wait state (clks1=clkb, 1.8v) 2 flash wait states (clks1=clkb, 1.8v) 2 flash wait states (clks1=clkb, 1.9v) : specified in "dc characteristics" www.datasheet.in
mb96340 series 118 fme-mb96340 rev 10 package dimension mb96(f)34x lqfp 100p please check the latest package dimension at the following url. http://edevice.fujitsu.com/package/en-search/ 100-pin pl as tic lqfp le a d pitch 0.50 mm p a ck a ge width p a ck a ge length 14.0 mm 14.0 mm le a d s h a pe g u llwing s e a ling method pl as tic mold mo u nting height 1.70 mm m a x weight 0.65 g code (reference) p-lfqfp100-14 14-0.50 100-pin pl as tic lqfp (fpt-100p-m20) (fpt-100p-m20) c 2005 fujit s u limited f1000 3 1 s -c-2-1 14.00 0.10(.551 .004) s q 16.00?.20(.6 3 0 .00 8 ) s q 1 25 26 51 76 50 75 100 0.50(.020) 0.20 0.05 (.00 8 .002) m 0.0 8 (.00 3 ) 0.145 0.055 (.0057 .0022) 0.0 8 (.00 3 ) "a" index .059 .004 +.00 8 0.10 +0.20 1.50 (mo u nting height) 0 ? ~ 8 ? (0.50(.020)) (.024 .006) 0.60 0.15 0.25(.010) 0.10 0.10 (.004 .004) det a il s of "a" p a rt ( s t a nd off) * dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s ?005-200 8 fujit s u microelectronic s limited f1000 3 1 s -c-2-2 note 1) * : the s e dimen s ion s do not incl u de re s in protr us ion. note 2) pin s width a nd pin s thickne ss incl u de pl a ting thickne ss . note 3 )pin s width do not incl u de tie ba r c u tting rem a inder. www.datasheet.in
mb96340 series fme-mb96340 rev 10 119 package dimension mb96(f)34x qfp 100p please check the latest package dimension at the following url. http://edevice.fujitsu.com/package/en-search/ 100-pin pl as tic qfp le a d pitch 0.65 mm p a ck a ge width p a ck a ge length 14.00 mm 20.00 mm le a d s h a pe g u llwing s e a ling method pl as tic mold mo u nting height 3 . 3 5 mm max code (reference) p-qfp100-14 20-0.65 100-pin pl as tic qfp (fpt-100p-m22) (fpt-100p-m22) c 2006-200 8 fujit s u microelectronic s limited f1000 33s -c-1-2 1 3 0 3 1 50 51 8 0 8 1 100 20.00?.20(.7 8 7?00 8 ) 2 3 .90?.40(.941?016) 14.00?.20 (.551?00 8 ) 17.90?.40 (.705?016) index 0.65(.026) 0. 3 2?.05 (.01 3 ?002) m 0.1 3 (.005) "a" 0.17?.06 (.007?002) 0.10(.004) det a il s of "a" p a rt (.0 3 5?006) 0. 88 ?.15 (.0 3 1?00 8 ) 0. 8 0?.20 0.25(.010) 3 .00 +0. 3 5 ?.20 +.014 ?00 8 .11 8 (mo u nting height) 0.25?.20 (.010?00 8 ) ( s t a nd off) 0~ 8 * * dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s . note 1) * : the s e dimen s ion s do not incl u de re s in protr us ion. note 2) pin s width a nd pin s thickne ss incl u de pl a ting thickne ss . note 3 ) pin s width do not incl u de tie ba r c u tting rem a inder. www.datasheet.in
mb96340 series 120 fme-mb96340 rev 10 ordering information mcu with can controller part number flash/rom subclock persistent low volt- age reset package MB96345ysa pqc-gse2 *1 rom (160kb) no yes 100 pin plastic qfp (fpt-100p-m22) MB96345rsa pqc-gse2 *1 no MB96345ywa pqc-gse2 *1 yes yes MB96345rwa pqc-gse2 *1 no MB96345ysa pmc-gse2 *1 no yes 100 pin plastic lqfp (fpt-100p-m20) MB96345rsa pmc-gse2 *1 no MB96345ywa pmc-gse2 *1 yes yes MB96345rwa pmc-gse2 *1 no mb96346ysa pqc-gse2 *1 rom (288kb) no yes 100 pin plastic qfp (fpt-100p-m22) mb96346rsa pqc-gse2 *1 no mb96346ywa pqc-gse2 *1 yes yes mb96346rwa pqc-gse2 *1 no mb96346ysa pmc-gse2 *1 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96346rsa pmc-gse2 *1 no mb96346ywa pmc-gse2 *1 yes yes mb96346rwa pmc-gse2 *1 no mb96f345fsb pqc-gse2 *1 flash a (160kb) data flash a (64kb) no yes 100 pin plastic qfp (fpt-100p-m22) mb96f345dsb pqc-gse2 *1 no mb96f345fwb pqc-gse2 *1 yes yes mb96f345dwb pqc-gse2 *1 no mb96f345fsb pmc-gse2 *1 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f345dsb pmc-gse2 *1 no mb96f345fwb pmc-gse2 *1 yes yes mb96f345dwb pmc-gse2 *1 no www.datasheet.in
mb96340 series fme-mb96340 rev 10 121 mb96f346ysb pqc-gse2 flash a (288kb) no yes 100 pin plastic qfp (fpt-100p-m22) mb96f346rsb pqc-gse2 no mb96f346ywb pqc-gse2 yes yes mb96f346rwb pqc-gse2 no mb96f346ysb pmc-gse2 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f346rsb pmc-gse2 no mb96f346ywb pmc-gse2 yes yes mb96f346rwb pmc-gse2 no mb96f346ysc pqc-gse2 *1 no yes 100 pin plastic qfp (fpt-100p-m22) mb96f346rsc pqc-gse2 *1 no mb96f346ywc pqc-gse2 *1 yes yes mb96f346rwc pqc-gse2 *1 no mb96f346ysc pmc-gse2 *1 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f346rsc pmc-gse2 *1 no mb96f346ywc pmc-gse2 *1 yes yes mb96f346rwc pmc-gse2 *1 no mb96f347ysb pqc-gse2 flash a (416kb) no yes 100 pin plastic qfp (fpt-100p-m22) mb96f347rsb pqc-gse2 no mb96f347ywb pqc-gse2 yes yes mb96f347rwb pqc-gse2 no mb96f347ysb pmc-gse2 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f347rsb pmc-gse2 no mb96f347ywb pmc-gse2 yes yes mb96f347rwb pmc-gse2 no mb96f347ysc pqc-gse2 *1 no yes 100 pin plastic qfp (fpt-100p-m22) mb96f347rsc pqc-gse2 *1 no mb96f347ywc pqc-gse2 *1 yes yes mb96f347rwc pqc-gse2 *1 no mb96f347ysc pmc-gse2 *1 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f347rsc pmc-gse2 *1 no mb96f347ywc pmc-gse2 *1 yes yes mb96f347rwc pmc-gse2 *1 no mcu with can controller part number flash/rom subclock persistent low volt- age reset package www.datasheet.in
mb96340 series 122 fme-mb96340 rev 10 mb96f348ysb pqc-gse2 flash a (544kb) no yes 100 pin plastic qfp (fpt-100p-m22) mb96f348rsb pqc-gse2 no mb96f348ywb pqc-gse2 yes yes mb96f348rwb pqc-gse2 no mb96f348ysb pmc-gse2 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f348rsb pmc-gse2 no mb96f348ywb pmc-gse2 yes yes mb96f348rwb pmc-gse2 no mb96f348ysc pqc-gse2 *1 no yes 100 pin plastic qfp (fpt-100p-m22) mb96f348rsc pqc-gse2 *1 no mb96f348ywc pqc-gse2 *1 yes yes mb96f348rwc pqc-gse2 *1 no mb96f348ysc pmc-gse2 *1 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f348rsc pmc-gse2 *1 no mb96f348ywc pmc-gse2 *1 yes yes mb96f348rwc pmc-gse2 *1 no mb96f348tsc pqc-gse2 flash a (544kb) flash b (32kb) no yes 100 pin plastic qfp (fpt-100p-m22) mb96f348hsc pqc-gse2 no mb96f348twc pqc-gse2 yes yes mb96f348hwc pqc-gse2 no mb96f348tsc pmc-gse2 no yes 100 pin plastic lqfp (fpt-100p-m20) mb96f348hsc pmc-gse2 no mb96f348twc pmc-gse2 yes yes mb96f348hwc pmc-gse2 no mb96v300brb-es (for evaluation) emulated by ext. ram yes no 416 pin plastic bga (bga-416p-m02) mcu with can controller part number flash/rom subclock persistent low volt- age reset package www.datasheet.in
mb96340 series fme-mb96340 rev 10 123 *1: these devices are under development and speci?ation is preliminary. these products under development may change its speci?ation without notice. this datasheet is also valid for the following outdated devices: mb96f346ysa, mb96f346rsa, mb96f346ywa, mb96f346rwa, mb96f347ysa, mb96f347rsa, mb96f347ywa, mb96f347rwa, mb96f348ysa, mb96f348rsa, mb96f348ywa, mb96f348rwa, mb96f348tsb, mb96f348hsb, mb96f348twb, mb96f348hwb, mcu without can controller part number flash/rom subclock package mb96f346asb pqc-gse2 flash a (288kb) no 100 pin plastic qfp (fpt-100p-m22) mb96f346awb pqc-gse2 yes mb96f346asb pmc-gse2 no 100 pin plastic lqfp (fpt-100p-m20) mb96f346awb pmc-gse2 yes mb96f346asc pqc-gse2 *1 no 100 pin plastic qfp (fpt-100p-m22) mb96f346awc pqc-gse2 *1 yes mb96f346asc pmc-gse2 *1 no mb96f346awc pmc-gse2 *1 yes mb96f347asb pqc-gse2 flash a (416kb) no 100 pin plastic qfp (fpt-100p-m22) mb96f347awb pqc-gse2 yes mb96f347asb pmc-gse2 no 100 pin plastic lqfp (fpt-100p-m20) mb96f347awb pmc-gse2 yes mb96f347asc pqc-gse2 *1 no 100 pin plastic qfp (fpt-100p-m22) mb96f347awc pqc-gse2 *1 yes mb96f347asc pmc-gse2 *1 no mb96f347awc pmc-gse2 *1 yes mb96f348asb pqc-gse2 flash a (544kb) no 100 pin plastic qfp (fpt-100p-m22) mb96f348awb pqc-gse2 yes mb96f348asb pmc-gse2 no 100 pin plastic lqfp (fpt-100p-m20) mb96f348awb pmc-gse2 yes mb96f348asc pqc-gse2 *1 no 100 pin plastic qfp (fpt-100p-m22) mb96f348awc pqc-gse2 *1 yes mb96f348asc pmc-gse2 *1 no mb96f348awc pmc-gse2 *1 yes mb96f348csc pqc-gse2 flash a (544kb) flash b (32kb) no 100 pin plastic qfp (fpt-100p-m22) mb96f348cwc pqc-gse2 yes mb96f348csc pmc-gse2 no 100 pin plastic lqfp (fpt-100p-m20) mb96f348cwc pmc-gse2 yes www.datasheet.in
mb96340 series 124 fme-mb96340 rev 10 mb96f346asa, mb96f346awa, mb96f347asa, mb96f347awa, mb96f348asa, mb96f348awa, mb96f348csb, mb96f348cwb www.datasheet.in
mb96340 series fme-mb96340 rev 10 125 revision history revision date modi?ation prelim 1 2007-05-07 creation prelim 2 2007-05-10 external bus hold timing update prelim 3 2007-05-23 electrical characteristics updates prelim 4 2007-08-02 electrical characteristics updates, product lineup, changes and ordering information prelim 5 2007-09-12 addition of the electrical characteristic examples and the lvd characteristics speci?ations, updates of the dc characteristics. pin circuit type drawing modi?ations. prelim 6 2007-11-21 lvd typo correction. update of the dc characteristics. typos corrections. prelim 7 2007-12-04 absolute maximum rating asterisks numbering corrected. typos page 59: hardware -> hardware. io map table regenerated. typos corrections. io circuit drawings modi?d. renaming of the main/satellite flash into flash memory a/b. memory map reworked. www.datasheet.in
mb96340 series 126 fme-mb96340 rev 10 prelim 8 2008-02-04 satellite flash -> 32kb data flash MB96345 added (under development) mb96f348 tsa/hsa/twa/hwa removed (outdated devices) block diagram and pin assignment corrected (existing resource pins) pin function table corrected i/o circuit type diagrams corrected memory map cleaned up "flash sector con?uration" replaced by corrected "user rom memory map for flash devices", ?om con?uration replaced by ?ser rom memory map for mask rom devices parallel flash programming pinning removed io map table regenerated: - port register: naming style corrected - memory control registers renamed (main/sat -> a/b) - addresses after 000bffh removed absolute maximum ratings: pd and ta speci?d more precisely oscillator input levels in oscillation mode with external clock added run and sleep mode currents: 96/48mhz and 72/36mhz settings added run mode current spec in 48/24mhz mode corrected maximum clks1/2 frequency for all devices correctly speci?d maximum clkp2 for mb96f34xy/r/axx corrected external bus timings: missing conditions added and readability improved alarm comparator spec updated (transition voltages de?ed) mb96v300a removed ordering information updated typos and formatting corrected revision date modi?ation www.datasheet.in
mb96340 series fme-mb96340 rev 10 127 9 2009-01-09 format adjusted to of?ial fujitsu microelectronics datasheet standard (mainly style changes and of?ial notes and disclaimer added) numbering of electrical characteristics subchapters automated note about devices under development modi?d i/o map: note added about reserved addresses iccspll for clks1=96mhz mode: increased by 1ma serial programming interface: note about handshaking pins improved speci?d ad converter channel offset to 4lsb package code of mb96v300 corrected in ordering information added voltage condition to pull-up resistance spec lineup: term ?ata flash?replaced by ?ndependent 32kb flash ordering information: column ?ndependent 32kb data flash replaced by new column ?lash/rom? column ?emarks?removed of?ial package dimension drawing with additional notes added empty pages removed alarm comparator: power supply current max values increased, comparison time reduced, mode transition time and power-up stabilization time newly added handling devices: notes added about serial communication and about using ceramic resonators. feature list and ac characteristics: 16mhz maximum frequency is valid for crystal oscillators. for resonators, maximum frequency depends on q-factor ac characteristics: pll phase skew spec added, clkvco min=64mhz vol3 spec improved: spec valid for 3ma load for full vcc range mb96f345 added preliminary dc spec of MB96345/346 added permitted power dissipation of flash devices in qfp package improved c-pin cap spec updated: 4.7uf-10uf capacitor with tolerance permitted ?reliminary?watermark removed revision date modi?ation www.datasheet.in
mb96340 series fme-mb96340 rev 10 10 2010-06-23 i/o map: ioabk0-5 added at address 000a00h-000a05h ordering information: suf? ??added to all mb96f345 device versions ad converter i ain spec improved: 1ua valid up to 105deg, 1.2ua above 105deg corrected mb96f345 part names in ordering information low voltage detector: detection levels of mb96f345 updated example characteristics updated, new ?ures added showing dependency of pll run mode current on frequency updated power supply current spec in run/sleep/timer/stop modes (new spec items in pll run/sleep mode, small adjustment of most other values) note added that pll phase jitter spec does not include jitter coming from main clock alarm comparator: maximum power-up stabilization time increased to 10ms removed phdr register from io map note added in dc characteristics how to select driving strength of ports i2c ac spec updated: tof, cb and tsp spec added, wrong footnotes and con- dition removed i/o circuit type: note added for type ? (slew rate control according to i2c spec) package dimension: added the following sentence under the ?ure: ?lease con?m the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ ad converter: impact of input pin capacitance and external capacitance added to formula for calculation of the sampling time added speci?ation of rc clock stabilization time feature description i2c: ?-bit addressing?corrected to ?-bit addressing feature description ppg: ?eload timer over?w as clock input corrected to ?eload timer under?w as clock input company name updated on the cover page: fujitsu microelectronics limited - > fujitsu semiconductor limited icclvd speci?ation updated, at 125deg typical value is 7ua and maximum value is 20ua ordering information: added devices under development mb96f346a*c, mb96f347a*c, mb96f348a*c, mb96f346y*c, mb96f347y*c, mb96f348y*c, mb96f346r*c, mb96f347r*c, mb96f348r*c revision date modi?ation www.datasheet.in
mb96340 series fme-mb96340 rev 10 129 www.datasheet.in
mb96340 series 130 fme-mb96340 rev 10 fujitsu semiconductor limited nomura fudosan shin-yokohama bldg. 10-23, shin-yokohama 2-chome, kohoku-ku yokohama kanagawa 222-0033, japan tel: +81-45-415-5858 http://jp.fujitsu.com/fsl/en/ for further information please contact: north and south america fujitsu microelectronics america, inc. 1250 e. arques avenue, m/s 333 sunnyvale, ca 94085-5401, u.s.a. tel: +1-408-737-5600 fax: +1-408-737-5999 http://www.fma.fujitsu.com/ europe fujitsu microelectronics europe gmbh pittlerstrasse 47, 63225 langen, germany tel: +49-6103-690-0 fax: +49-6103-690-122 http://emea.fujitsu.com/microelectronics/ korea fujitsu microelectronics korea ltd. 206 kosmo tower building, 1002 daechi-dong, gangnam-gu, seoul 135-280, republic of korea tel: +82-2-3484-7100 fax: +82-2-3484-7111 http://kr.fujitsu.com/fmk/ asia paci? fujitsu microelectronics asia pte. ltd. 151 lorong chuan, #05-08 new tech park 556741 singapore tel : +65-6281-0770 fax : +65-6281-0220 http://www.fmal.fujitsu.com/ fujitsu microelectronics shanghai co., ltd. rm. 3102, bund center, no.222 yan an road (e), shanghai 200002, china tel : +86-21-6146-3688 fax : +86-21-6335-1605 http://cn.fujitsu.com/fmc/ fujitsu microelectronics pacific asia ltd. 10/f., world commerce centre, 11 canton road, tsimshatsui, kowloon, hong kong tel : +852-2377-0226 fax : +852-2376-3269 http://cn.fujitsu.com/fmc/en/ specifications are subject to change without notice. for further information please contact each office. all rights reserved. the contents of this document are subject to change without notice. customers are advised to consult with sales representatives before ordering. the information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of fujitsu semiconductor device; fujitsu semiconductor does not warrant proper operation of the device with respect to use based on such information. when you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. fujitsu semiconductor assumes no liability for any damages whatsoever arising out of the use of the information. any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of fujitsu semiconductor or any third party or does fujitsu semiconductor warrant non-infringement of any third-party's intellectual property right or other right by using such information. fujitsu semiconductor assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. the products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). please note that fujitsu semiconductor will not be liable against you and/or any third party for any claims or damages aris- ing in connection with above-mentioned uses of the products. any semiconductor devices have an inherent chance of failure. you must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over- current levels and other abnormal operating conditions. exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the foreign exchange and foreign trade control law of japan and/or us export control laws. the company names and brand names herein are the trademarks or registered trademarks of their respective owners. edited: sales promotion department www.datasheet.in

▲Up To Search▲

Price & Availability of MB96345

	To Download MB96345 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .